XP-Manager 3.20

Chap.1 Starting
1-1
Chap. 1 Starting
1.1 The characteristics of XP-Manager
XP-Manager that supports various functions of XGT Panel realizes data communication between XGT Panels through XP Link.
This software has the below characteristics and strong points.
(1) You can change freely the position and composition of a screen.
(2) It can be changed for the convenience of users through user defined hot key and tool bar.
(3) It is composed of shortcut icon for a userto apply the functions more easily.
Chap.1 Starting
1-2
(4) It can be edited easily through Drag& Drop between screens.
Chap.1 Starting
1-3
(5) You can freely perform Undo and Redo at edition screen.
(6) You can monitor the device of XGT Panel.
(7) You can monitor the screen of XGT Panel at PC through VNC function.
Chap.1 Starting
1-4
(8) You can download the backup file of XGT Panel through web server.
(9) You can monitor the screen of XGT Panel through web-server.
Chap.1 Starting
1-5
1.2 System Requirements to execute XP-Manager
(1) Personal computer and memory
The computer with Pentium 4 CPU and 512MB memory or more is needed.
(2) Communication Port
Ethernet Port is required.
(3) Hard Disk
The available area of 100MB or more is required.
(4) Mouse
A mouse to be connected to a computer is needed.
(5) Monitor
The resolution should be more than 1024 x 768.
(6) Computer Operation System
It can be executed at Windows 2000 version or more.
Chap.1 Starting
1-6
1.3 XP-Manager Installation
[Installation Procedures]
(1) Execute the installation file.
(2) Select the language to be installed.
(3) Installation Wizard prepare for installation as below.
(4) Starting XP-Manager installation will be displayed as below. Press [Next] button to continue installation.
Chap.1 Starting
1-7
(5) After inputting user information, press Next button.
(6) Designate the position of folder where XP-Manager will be installed. XP-Manager requires the space of
approximately 100MB for installation so check the installation folder has enough space. If installation space is not
Chap.1 Starting
1-8
enough, next process will not proceed with a warning message. After selecting the folder, press [Next] button.
(7) It is ready to be installed. If you press Installation button, installation process will start.
Chap.1 Starting
1-9
(8)It shows the progress status of installation.
(9) If you press Finish, installation process will be terminated normally.
Chap.1 Starting
1-10
(10) You can work by executing XP-Manager at [Start] menu or executing Shortcut icon of home screen.
[Deletion Procedures]
(1) To delete XP-Manager, select [XP-Manager Deletion] at [Start Menu] or apply [Add/Remove Programs] function
of control board.
(2) Select Yes.
Chap.1 Starting
1-11
(3) The information of installed programs is collected and program deletion will be in progress.
Notice
(1) In case that XP-Manager is in progress, you can not delete it. Then, after terminating XP-Manager first, delete it.
(2) For installation under Windows Vista and Windows 7, note the below.
* You are required to log in as an Administrator to install XP-Builder.
* After installation, set up the security procedures as below.
1) Click Start->Settings and execute Control Panel.
2) Click Control Panel->User Accounts.
Chap.1 Starting
1-12
3) Click the related icon at a user accounts setting screen.
Chap.1 Starting
1-13
4) Click Turn User Account Control on or off at User Administrator at User Account Setup screen.
Chap.1 Starting
1-14
5) Disable [Use user Account Control to help protect your computer].

Chap.2 XP-Manager Outline and Practice
2-1
Chap.2 XP-Manager Outline and Practice
2.1 XP-Manager Outline
2.1.1 Definition of XP-Manager
It is the software for edition, download, monitoring to realize data communication between XGT Panels through XP
Link with online control function.
2.1.2 The interrelation of XP-Manager and XP-Builder
XP-Builder is the software to draw the screen of XGT Panel. It can be saved as a project file (XPD file) or you can also
download the project to XGT Panel. XP-Manager opens the project file (XPD file) made by XP-Builder and collects PLC
Driver, Tag information to apply them.
(a) Using the XPD file of a computer

(b) Using the uploaded project of XGT Panel

Notice
(1) The project file (XPD file) made by XP-Builder version 1.21 or more is available,
(2) It is available at XGT Panel version 1.21 or more.
(3) For details, refer to Chap. 4.1.
Chap.2 XP-Manager Outline and Practice
2-2
2.2 Practice
A user can briefly learn how to use XP-Manager through the below practice processes.
2.2.1 Adding Node
[Procedures]
(a) Select [Start Menu]-[Program]-[LS]-[XP-Manager] and execute XP-Manager.
(b) Turn on the power of XGT Panel.
(c) Download “LS: XGK (CPU)”project through XP-Builder and make sure to activate [Include upload
project file option] to check the project information from XP-Manager.
(c) Check whether there is the target XGT Panel at online screen of XP-Manager.
Chap.2 XP-Manager Outline and Practice
2-3
(d) Drag & Drop the target XGT Panel to a project screen.
Chap.2 XP-Manager Outline and Practice
2-4
(e) If the dialog box to add a new node is shown, press OK button.
(f) Read the project file (XPD file) through communication.
Chap.2 XP-Manager Outline and Practice
2-5
Notice
(1) In case that the target XGT Panel is less than version 1.21, you can not upload a project file.
(2) If there is no uploaded project at the target XGT Panel, upload is not available.
(3) For details, refer to the Chap. 4.1.
(4) USB cable is scheduled to be provided afterward.
(g) If reading process is normally over, node will be added.
2.2.2 Editing Device Communication
You are required to make the below parameters for device communication between XGT Panels through XP Link.
[Procedures]
(a) Add two or more nodes to a project.
(b) Double-click Device Communication at a project screen to open it.
Chap.2 XP-Manager Outline and Practice
2-6
(c) Double-click the column to be edited.
(d) After selecting reading or writing mode depending on required operation, you can edit operation device
Chap.2 XP-Manager Outline and Practice
2-7
and object device.
(e) Edit the device communication as you may need.
2.2.3 Editing Trigger Condition
You can edit trigger condition when specific condition is fulfilled or in order to start an event at the proper time.
[Procedures]
(a) Double-click trigger condition at a project screen.
Chap.2 XP-Manager Outline and Practice
2-8
(b) Double-click the column to be edited.
(c)After editing bit device, word device, time trigger, system trigger depending on the required conditions, edit them.
Chap.2 XP-Manager Outline and Practice
2-9
(d) To connect device communication to trigger, double-click the below position.
(e) Double-click the device communication to be connected from the list.
Chap.2 XP-Manager Outline and Practice
2-10
(f) Edit the trigger conditions as you may need and connect device communication.
Chap.2 XP-Manager Outline and Practice
2-11
2.2.4 Downloading XP Link Parameter
You need to download parameters for data communication between XGT Panels.
[Procedures]
(a) Save the project.
(b) Select [Communication]-[Download XP-Link Parameter] menu.
(c) After checking the target object, download it.
Chap.2 XP-Manager Outline and Practice
2-12
(d) If download process is completed, press XGT Panel Start button for monitoring.
Check if device communication works smoothly and device values are properly displayed based on established trigger
conditions.
2.2.5 Monitoring
To check if device communication and trigger condition work properly, you may need a remote computer. You can easily
check the status through monitoring function.
[Procedures]
(a) Save the project.
(b) After selecting the items to be monitored at device communication screen or trigger condition screen, Drag & Drop
them to a monitoring screen.
Chap.2 XP-Manager Outline and Practice
2-13
(c) Press Start Monitoring button and monitor the status.
(d) If communication works properly, the registered device value will be displayed.
Chap.2 XP-Manager Outline and Practice
2-14
Notice
(1) Only when XGT Panel is under monitoring process, XP-Manager can realize the function.
(2) For details, refer to the Chap. 11.

Chap.3 Composition of XP-Manager
3-1
Chap.3 Composition of XP-Manager
3.1 The Composition of a Screen

The screen of XP-Manager is composed of the below.
[Screen Description]
Item Description
Title Bar(a) The tile is displayed as project name+ XP-Manager at Windows screen.
Menu Bar(b) It is the basic menu for the program.
Too Bar(c) The button is to execute shortcut menu.
Project Screen(d) It displays the components of a project. For edition, double-click the item.
Edition Screen(e) There are the screens for tag, device communication, and trigger condition.
Online Screen(f) It detects the XGT Panel of network.
Output Screen(g) It displays the result of program inspection or device search.
Monitor Screen(h) It can monitor the device of XGT Panel.
Status Bar(i) It displays the description of selected menu or operation.
(a)
(b)
(c)
(d) (e)
(f)
(g) (h)
(i)
Chap.3 Composition of XP-Manager
3-2
3.2 The Composition of Menu
The description on XP-Manager menu will be provided. In the case of the menu where hot key is displayed, you can just press it
to execute command.
(1) Project
Command Description
New Project It closes opened project and creates a new project.
New Node It adds node to a project.
Open It closes opened project and open a new project.
Close It closes opened project.
Save It saves opened project.
Save as Opened project is saved as another name.
Import Node It imports the node exported previously.
Export Node It exports selected node.
Print It prints the current screen.
Print Settings It changes the property of print
Print Preview It previews the current screen before printing.
Latest Files It shows the latest opened files.
Exit It terminates XP-Manager.
Chap.3 Composition of XP-Manager
3-3
(2) Edition
Command Description
Undo Edition It backs to the last edited contents. Edition data is operated
individually for each screen.
Redo Edition It performs Redo Edition. Edition data is operated individually for
each screen.
Delete It deletes the selected item of active screen
Cut It copies the selected item of active screen to a clipboard and cut it.
Copy It copies the selected item of active screen to a clipboard.
Paste It pastes the last copied item to the selected area.
Delete All It deletes all items of active screen.
Find It searches for the device
Replace It changes the device.
Go to It moves to the specific column of a screen.
Select All It selects all items of active screen.
(3) View
Chap.3 Composition of XP-Manager
3-4
Command Description
Tools
Project It hides project tool bar.
Edit It shows or hides edition tool bar.
Online It shows or hides online tool bar.
View It shows or hides view tool bar
Tools It shows or hides tool bar.
Customize It can change menu, tool, hot key, etc.
Status Bar It shows or hides status bar.
Online Window It shows or hides online screen.
Project Window It shows or hides project screen.
Output Window It shows or hides output screen.
Monitor Window It shows or hides monitor screen.
Full Screen It hides all tool bars and menus to maximize the current screen.
Properties It shows the registration information of selected item.
(4) Communication
Command Description
Download XP Link Parameter You can download XP Link parameter by selecting node.
Upload XP Link Parameter You can upload XP Link parameter.
Manage XP-VNC Server You can install, delete XP-VNC server of selected XGT Panel and
change the operation mode.
Manage Web Server You can install, delete web server of selected XGT Panel and
change the operation mode.
Manage Driver You can change RAPIEnet program monitor settings of selected
XGT Panel.
Update XGT Panel You can update XP-Runtime of XGT Panel.
XGT Panel Information You can see the information of selected XGT Panel change the
setting details.
(5) Tool
Chap.3 Composition of XP-Manager
3-5
Command Description
Check Program You can check the error of opened project.
Start XP-Builder You can execute XP-Builder.
Start XP-VNC You can execute XP-VNC.
Start XP-Explorer You can execute XP-Explorer.
Customize You can change menu, tool, hot key, etc.
Option You can change the options of XP-Manager.
(6) Screen
Command Description
New Window It opens another window that is the same with active one.
Close All It closes all opened screens.
(7) Help
Command Description
XP-Manager Help It executes Help File for XP-Manager
About XP-Manager It displays the version information and license details of XP-Manager.
Chap.3 Composition of XP-Manager
3-6
3.3 The Composition of Tool Bar
(1) Project
Command Image Description
New Project It closes opened project and creates a new project.
Add Node It adds a node to a project.
Open It closes opened project and open a new project.
Save It saves opened project.
Print It prints the current screen.
Print Preview It previews the current screen before printing.
(2) Edition
Command Image Description
Undo Edition It backs to the last edited contents. Edition data is operated individually for each
screen.
Redo Edition It performs Redo Edition. Edition data is operated individually for each screen.
Delete It deletes the selected item of active screen
Cut It copies the selected item of active screen to a clipboard and cut it.
Copy It copies the selected item of active screen to a clipboard.
Paste It pastes the last copied item to the selected area.
Chap.3 Composition of XP-Manager
3-7
(3) Online
Command Image Description
Download XP Link
Parameter You can download XP Link parameter by selecting node.
Upload XP Link Parameter You can upload XP Link parameter.
Manage XP-VNC Server You can install, delete XP-VNC server of selected XGT Panel and change the
operation mode.
Manage Web Server You can install, delete web server of selected XGT Panel and change the
operation mode.
Manage Driver You can change RAPIEnet program monitor settings of selected XGT Panel.
Update XGT Panel You can update XP-Runtime of XGT Panel.
XGT Panel Information You can see the information of selected XGT Panel change the setting details.
(4) Window
Command Image Description
Project Window It shows or hides projectWindow.
Online Window It shows or hides online Window.
Output Window It shows or hides output Window.
Monitor Window It shows or hides monitor Window.
(5) Tool
Command Image Description
Start XP-Builder It executes installed XP-Builder.
Start XP-VNC It executes XP-VNC.
XP-Server It executes XP-Server
Help It executes Help File.
Chap.3 Composition of XP-Manager
3-8
3.4 Docking Window
The windows (project screen, online screen, output screen, monitor screen) that you can see from View Menu can be
docked. You can adjust the position and size of windows and they can be docked to any position. Furthermore, you can
keep docking screen being floated or use Auto-Hide function.
(1) Moving the position of docking screen
The below is docking position guile line that is shown when moving tool screen. If you drag and move the title of the
screen, docking guide will be shown at the screen. If you put the screen to the center of docking guide, it will be docked to
your intended position easily.
The window to be
docked
Docking guide
Chap.3 Composition of XP-Manager
3-9
(2) Changing into floating Windows
Select [Floating] menu by clicking docking window title to be floated with a right mouse button.
(3) Auto-Hide Mode
If you select [Auto-Hide] menu on the title of docking window or press a tack button of below docking window, windows
will disappear automatically.
If you put a mouse to the center of
docking guide, tab type of shadowy
Windows will guide the position to be
docked.
Windows hidden by AutoHide Mode
Chap.3 Composition of XP-Manager
3-10

Chap. 4 Project
4-1
Chap.4 Project
4.1 Add Nodes
XP-Manager creates automatically blank project at the moment it is executed. Then, you can directly add nodes.
4.1.1 The Definition of Node
A node means one termination XGT Panel between XP Link communications. The IP of nodes cannot be overlapped. Nodes
have the information on XGT Panel type, PLC Driver, Device communication, trigger condition, tag of the project.
[Nodes of XP-Manager]
[Nodes of Network]
Node 1 Node 2 Node 3 Node 4
Node
Chap. 4 Project
4-2
Notice
(1) The IP of node cannot be overlapped within XP-Manager.
(2) The IP of XGT Panel cannot be overlapped in network. In case that the IP is overlapped, unexpected error can occur
due to IP conflict. In this case, contact the network administrator to solve the problem.
4.1.2 Manual Configuration by adding nodes directly
[Procedures]
(1) Select [Project]-[New Node] menu.
(2) Input the name of node (a) and the target XGT Panel’s IP address(c).
(3) Select [Manual creation by adding directly] (d) button.
(4) Press Change (f) button and add XGT Panel and PLC Driver.
(a)
(b)
(c)
(d)
(e)
(f)
Chap. 4 Project
4-3
(5) Change the type of XGT Panel and select the type.
(6) Select the vendor and controller (h). If necessary, press Add (i) button, add a controller.
(7) Press OK (l) button to save the contents.
(8) Press OK (e) button to add a node.
(9) Add a node to project screen.
[Description on a dialog box]
Item Description
Name (a) The name of node can be input up to 255 characters and special characters are also available.
However it cannot be overlapped with other node name.
Description(b) You can input comment without length limit.
Target XGT Panel’s IP
address (c)
It inputs the IP address of the only XGT Panel in network and it cannot be overlapped within
project.
Manual creation by
adding directly (d)
You can input manually the information of XGT Panel and PLC Driver for your convenience.
OK(e) It saves the contents of a dialog box and closes it and adds a node.
Change(f) It can change the model of XGT Panel or add/change/delete PLC Driver.
XGT Panel Model(g) You can select the model of XGT Panel.
Select Controller (h) It shows the manufacturer and PLC driver list.
Add(i) You can add PLC Driver up to 4EA.
Delete (j) It deletes the selected PLC Driver from the list. In case that there is only one driver, you cannot
delete it.
OK(k) It saves the changed contents and closes a dialog box.
(g)
(h)
(i) (j) (k) (l)
Chap. 4 Project
4-4
Undo(l) It closes a dialog box without saving the changed contents.
[Screen]
[Description on screen]
Item Description
Project(a) The name of project is displayed.
Node (b) The name of node and target XGT Panel’s IP address are displayed.
Tag 1(c) The tag can be declared at XP-Manager.
Tag 2: XP-Builder(d) In case of node uploaded from XGT Panel or added from XP-Builder file, it is the tag
declared by XP-Builder,
Device Communication(e) It can define the communication contents between nodes.
Trigger Condition (f) It can designate the operation condition of device communication.
Notice
(1) The name of node can be designated up to 255 characters.
(2) If there is no name of node, it cannot be set as node.
(3) The name of node cannot be overlapped within project.
(a)
(b)
(c)
(d)
(e)
(f)
Chap. 4 Project
4-5
(4) The IP address of target XGT Panel of node cannot be overlapped within project.
4.1.3 Automatic Configuration form XP-Builder file of a computer
You can add nodes through the project file (XPD file) made by XP-Builder.
[Procedures]
(1) Select [Project]-[New Node] menu.
(a)
(b)
(c)
(d)
(e)
(f)
Chap. 4 Project
4-6
(2) Input the name of node (a) and IP address(c) of XGT Panel.
(3) Select (d) button [Auto creation from XP-Builder file of a computer.
(4) Search for XP-Builder project file (XPD file) with Explorer (f) button.
(5) Press Open (g) button after finding XP-Builder project file.
(6) Press OK (e) button to add node.
(7) Node will be added to the project screen.
[Description on a dialog box]
Item Description
Name (a) The name of node can be input up to 255 characters and special characters are
also available. However it cannot be overlapped with other node name.
Description (b) You can input comment without length limit.
Target XGT Panel’s IP address (c) It inputs the IP address of the only XGT Panel in network and it cannot be
overlapped within project.
Auto creation from XP-Builder
file of a computer (d)
You can open XP-Builder file(XPD file) and import the information of XGT Panel
type and PLC Driver, tag to configure node.
OK(e) It saves the contents of a dialog box and closes it and adds a node.
Change(f) It can change the type of XGT Panel or add/change/delete PLC Driver.
Open(g) It opens selected file.
(g)
Chap. 4 Project
4-7
Notice
(1) You cannot open the XP-Builder file made by under XP-Builder 1.21.
(2) You can re-use the tag made by XP-Builder but edition is not available.
Chap. 4 Project
4-8
4.1.4 Auto Creation from XGT Panel in Network
You can upload XP-Builder project from XGT Panel in network and add a new node. XP-Builder project file is uploaded from the
target XGT Panel.
[Procedures]
(1) Select [Project]-[New Node] menu.
(2) Input the name of node (a) and IP address(c) of target XGT Panel.
(3) Select Automatic Configuration (d) button from XGT Panel of network.
(4) Press OK (e) to add a node.
(5) Communication dialog box will be shown and the project is uploaded from XGT Panel.
(a)
(b)
(c)
(d)
(e)
Chap. 4 Project
4-9
(6) The node is added to a project screen.
Chap. 4 Project
4-10
[Description on a dialog Box]
Item Description
Name (a) The name of node can be input up to 255 characters and special characters are
also available. However it cannot be overlapped with other node name.
Description(b) You can input comment without length limit.
Target XGT Panel’s IP address (c) It inputs the IP address of the only XGT Panel to be uploaded in network and it can
not be overlapped within project.
Auto creation from XGT Panel in
network (d)
It reads the uploaded project from XGT Panel of IP address in target XGT Panel
and adds a node.
OK(e) It saves the contents of a dialog box and closes it and adds a node.
Change(f) It can change the type of XGT Panel or add/change/delete PLC Driver.
Open(g) It opens selected file.
Notice
(1) In case that password is set for XGT Panel, you need to check the password for upload.
(2) You cannot open the XP-Builder file made by under XP-Builder 1.21.
(3) You can re-use the tag made by XP-Builder but edition is not available.
Chap. 4 Project
4-11
4.2 Node Deletion
You can delete the added node.
[Procedures]
(1)Select the node to be deleted from a project screen.
(2) Select [Edit]-[Delete] menu or select [Delete] context menu.
Chap. 4 Project
4-12
(3) Then, the node is deleted.
Notice
(1) You cannotrestore the deleted node with Undo Edition.
(2) It is possible there is no node in project.
Chap. 4 Project
4-13
4.3 Changing the Properties of Node
You can change the properties of added node.
[Procedures]
(1)Select the node whose properties should be changed from a project screen.
(2) Select or double-click [View]-[Properties].
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
(j)
(k)
(l) (m) (n)
(p)
(o)
Chap. 4 Project
4-14
(3) After changing the properties of node, save it with OK button.
[Description on a dialog Box]
Item Description
Name (a) The name of node can be input up to 255 characters and special characters
are also available. However it cannot be overlapped with other node name.
Description(b) You can input comment without length limit.
Target XGT Panel’s IP address (c) It inputs the IP address of the only XGT Panel in network and it cannot be
overlapped within project.
How to create node (d) In case that the method to configure node is changed, it is renewed from the file
and the file and XGT Panel.
Manual creation by adding directly(e) You can manually input the information of XGT Panel and PLC Driver for your
convenience.
Auto creation from XP-Builder file of a
computer(f)
It opens XP-Builder project file(XPD file) and imports the information on XGT
Panel type and PLC Driver, tag to configure a node.
Position of XP-Builder project file(g) It shows the selection route of XP-Builder file (XPD file).
Auto creation from XGT Panel in
network (h)
It reads the uploaded project from the IP address of target XGT Panel and
adds a node.
XGT Panel Information (i) It shows the information of XGT Panel and PLC Driver saved at a node.
XGT Panel model (j) It shows the information of XGT Panel saved at a node.
Controller List (k) It shows the information of PLC Driver saved at a node.
Refresh(l)
In case that a node is XP-Builder configured automatically from XP-Builder file
of a computer or it is configured automatically from XGT Panel of network, it is
active. For refresh, XPD file is read again or it is re-uploaded from XGT Panel.
OK (m) It saves the contents of a dialog box and closes it.
Undo(n) It closes a dialog box without saving the contents.
Explorer Button (o) In case the node is automatically configured from XP-Builder of a computer,
you can select XP-Builder project file.
Change(p) If the node is added and manually configured, you can change the XGT Panel
type and PLC Driver.
Notice
(1) If you try to change the IP address of target XGT Panel, press the renewal button.
(2) If the properties of node configuration mode are changed, it is renewed automatically.
(3) Only when node is added directly and configured manually, you can change the XGT Panel type and PLC Driver.
Chap. 4 Project
4-15
4.4 Exporting Node
To reuse the node of a project, you can export it.
[Procedures]
(1)Select the node to be exported from a project screen.
(2) Select [Project]-[Export Node] menu or select [Export Node] of context menu.
(3) Select the position for exporting a node and input the name of file.
Chap. 4 Project
4-16
(4) Press Save button to save the file.
Notice
(1) The file extension of exporting a node is XMN.
(2) You cannot input special characters to a file name.
(3) You cannot open the exported file directly at XP-Manager. Use Importing Node menu.
Chap. 4 Project
4-17
4.5 Importing Node
You can import the file (XMN file) made by Exporting Node as a project with Importing Node function.
[Procedures]
(1)Select [Project]-[Import Node] menu or select [Import Node] of context menu.
Chap. 4 Project
4-18
(2)Select the file to be imported and press Open button.
(3)If the Node Properties dialog box is shown, press OK button to add a node.
Notice
(1) The name of imported node cannot be overlapped so change the name.
(2) In the case of imported node, the IP address of target XGT Panel cannot be overlapped so change the IP address.
Chap. 4 Project
4-19
4.6 Copy/Paste Node
You can copy the node to a clipboard and paste it to other XP-Manager.
[Procedures]
(1)Select the node to be copied from a project screen.
(2)Select [Edition]-[Copy] menu or select [Copy] of context menu. No changes occur.
(3)Select [Edition]-[Paste] menu or select [Paste] of context menu.
(4)The Node Properties dialog box will be shown and press OK button to press OK button.
Notice
(1) The node copied to a clipboard can be pasted to other XP-Manager.
The copied contents remain at a clipboard before other copy process proceeds.
Chap. 4 Project
4-20
4.7 Cut/Paste Node
Copy the node to a clipboard and delete it from a project. You can paste the copied node to other XP-Manager.
[Procedures]
(1)Select the node to be cut from a project screen.
(2)Select [Edition]-[Cut] menu of select [Cut] of context menu.
(3)Then, selected node is deleted and it is copied to a clipboard.
(4)Select [Edition]-[Paste] menu or select [Paste] of context menu.
(5)The Node Properties dialog box will be shown. Press OK button to add a node.
Chap. 4 Project
4-21
Notice
(1) Undo Edition for a cut node is not available.
(2) The node be copied to a clipboard can be pasted to other XP-Manager.
(3) The copied contents remain at a clipboard before other copy process proceeds.
Chap. 4 Project
4-22
4.8 Configuring a Project
You can close the opened project and configure a blank project.
[Procedures]
(1)Select [Project]-[New Project] menu.
(2)If there is opened project, the project is closed.
(3)Configure a blank project again.
Notice
(1) If the opened project is edited, check if it is saved when the project is closed.
Chap. 4 Project
4-23
4.9 Changing the properties of project
You can change the name and comment of a project.
[Procedures
(1)Select the name of project from a project screen.
(2)Select or double-click [View]-[Properties] menu.
(3)Then, the dialog box on project properties information will be shown.
(4)Change the properties and press OK button.
[Description on a dialog box]
Item Description
Name(a) You can input the name of a project without limitation on length, special characters.
Description (b) You can input comment without limitation on length.
File path (c) When the project is saved, it shows the route of saved file.
OK(d) It saves the contents of a dialog box and closes the box.
Cancel (e) It closes a dialog box without saving the contents.
(a)
(b)
(c)
(d) (e)
Chap. 4 Project
4-24
4.10 Saving Project
You can save the project as a file.
[Procedures]
(1)Select [Project]-[Save] menu.
(2)If you open the saved file, the project is continuously saved at the previous file.
(3)If the file is saved for the first time, Save As dialog box will be shown.
(4)Input the file name and press [Save] button.
Notice
(1) The file extension of the project used for XP-Manager is XMU file.
(2) If the file opened at other project is saved, Sharing Violation error will occur.
(3) If “Display the message in case that a file name is different form project name when saving” is set at [Option]-[Project],
the below message will be shown for saving.
If “Yes” is selected, it changes the project name into file name and saves it. If [No] is selected, it is saved as before.
Chap. 4 Project
4-25
(4) If the project is edited, an asterisk is marked with the rear of project name. If it is saved as a file, an asterisk will disappear.
Chap. 4 Project
4-26
4.11 Project Save As
You can open the saved file and save it as another name.
[Procedures]
(1)Select [Project]-[Save As] menu.
(2)Input the file name and press [Save] button.
Chap. 4 Project
4-27
4.12 Close Project
It closes the opened project.
[Procedures]
(1)Select [Project]-[Exit] menu.
(2)If project edition is completed, the message to confirm Save.
(3)If [Yes] is selected, it saves the changed details and closes the project.
(4)If [No] is selected, it closes the project without saving the changed details
(5)If “Cancel” is selected, it discontinues closing the project.
Chap. 4 Project
4-28
4.13 Open Project
You can open the XP-Manager project file (XMU file) saved previously to open project.
Notice
(1) If you try to open the file is used by other XP-Manager or Read Only file, the below message will be shown.
If “Yes”is selected, you can open the project as Read Only mode to save it as another name. If [No] is selected,
Open Project process is suspended.
4.13.1 Open Project Dialog Box
When XP-Manager is executed, you can promptly open the previous project through the Open Project Dialog Box.
[Procedures]
(1)Execute XP-Manager.
(2)When starting [Tool]-[Option]-[Project] menu, if the option displaying the Open Project Dialog Box is active, the dialog
box will be shown.
Chap. 4 Project
4-29
(3)Select the project from the dialog box to open project and press OK button.
[Description on a dialog box]
Item Description
Open existing project(a) It opens file explorer and searches for the project file to open it.
Open recent project (b) It opens the selected project from the latest project list(c).
Recent Project List(c) It shows the list of previous projects
Show full path (d) It shows the whole route of file from the latest project list.
Hide this dialog box (e) Project Open dialog box will not be shown when the next XP-Manager is executed.
OK(f) It opens the project based on selected options.
Cancel(g) It configures a blank project without opening project.
4.13.2 Opening from the latest project
You can promptly select and open the project from the latest list
[Procedures]
(a)
(b)
(c)
(d) (e) (f) (g)
Chap. 4 Project
4-30
(1)Select the project to be opened from the latest list of [Project] menu.
(2)The opened project is closed and selected project is opened.
4.13.3 Opening file by explorer
[Procedures]
(1)Select [Project]-[Open] menu.
Chap. 4 Project
4-31
(2)After selecting the target file, press [Open] button to open the project.
4.13.4 Opening file by double-click at Windows Explorer
[Procedures]
(1)Execute Windows Explorer.
(2)Double-click the XP-Manager project file to be opened.
(3)XP-Manager is executed newly and the project is opened.
4.13.5 Opening file by Drag & Drop at Windows Explorer
[Procedures]
Chap. 4 Project
4-32
(1)Execute Windows Explorer.
(2)Execute XP-Manager.
(3)Drag & Drop the XP-Manager project file (XMU file) to be opened at Windows Explorer.

Chap.5 Tag
5-1
Chap. 5 Tag
5.1 Definition of Tag
Tag is the function to pre-register the device address and type (Bit, Word) frequently used with the name in advance to manage
the device easily and conveniently. Device address can be expressed as the name that a user can recognize.
The tag of XP-Manager is the same as that used for XP-Builder but two tags are allowable depending on node configuration
type. There are two tags configured by XP-Manger and XP-Builder.
[Regulations for Tag Name]
Number A number can not be used for the first character of a name. (Ex. 3ABCD)
Special Characters Special characters are not available except ‘_’
Space The space added to the front and rear of a name is not recognized as a name.
Device Name The address of connected PLC can not be used for the name.(Ex. D0012, %MW123)
Hexadecimal Hexadecimal such as H234 can not be used for the name
5.1.1 The node added directly and configured manually
There is only the tag screen for XP-Manager.
(a)
Chap.5 Tag
5-2
[Description]
Item Description
Tag 1(a) It is the tag configured from XP-Manager. The tag for XP-Manager can be edited.
Tag Screen (b) It is the tag screen for XP-Manager that can be edited.
5.1.2 The Node configured automatically from XP-Builder file of a computer
There are the tags for XP-Manager and the tag screen created by XP-Builder.
(b)
(b)
(a)
Chap.5 Tag
5-3
[Description]
Item Description
Tag 1(a) It is the tag configured from XP-Manager. The tag for XP-Manager can be edited.
Tag 2: XP-Builder(b) It is the tag created by XP-Builder and read from the file. XP-Builder tag can not be edited.
Tag Screen (c)
It is the tag screen for XP-Builder that can not be edited. In case that edition is not
available, the background color is gray.
5.1.3 Node configured automatically from the file of network
There is the tag for XP-Manager and tag screen configured from XP-Builder.
(c)
(a)
(b)
Chap.5 Tag
5-4
[Description]
Item Description
Tag 1(a) It is the tag created from XP-Manager. The tag for XP-Manager can be edited.
Tag 2: XP-Builder(b) It is the tag created from XP-Builder and read from the file. XP-Builder can not be edited.
Tag Screen (c) It is the tag screen for XP-Builder that can not be edited. In case that edition is not
available, the background color is gray.
(c)
Chap.5 Tag
5-5
5.2 Tag Declaration
You need to declare tag at tag screen in advance before using tag.
[Procedures]
(1) Select [Tag 1] from a project screen and select or double-click [View]-[Properties] menu.
(2) Select [Default] tag group.
(3) Input the tag name to [Name] column at tag screen.
(4) Select the device column and press device button.
Chap.5 Tag
5-6
(5) Select the device.
(6) If necessary, input the comment.
[Description on a dialog box]
Item Description
Tag(a) The button converts the Device Selection Dialog Box into Tag Selection Dialog box.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h) (i)
(j)
(k)
Chap.5 Tag
5-7
PLC Driver Selection(b)
You can select other PLC Driver from the list displayed at Node Registration
Information.
Device Selection(c) You can change the kind of device.
Current Input Device (d) It displays the whole name of the inputted device at the Device Setting Dialog Box.
Device Information(e) It shows the information and maximum address of the selected device(c).
Designating network unit
number (f)
You can change the unit number of target device.
Network Unit No.(g) You can input the unit number.
OK(h) It saves the contents of a dialog box and closes the box.
Cancel (i) It closes a dialog box without saving the contents of a dialog box.
Number Pad(j) It helps for you to input device.
Offset(k) It changes the offset of device.
Notice
(1) You can declare the tags up to 1000EA per tag group.
Chap.5 Tag
5-8
5.3 Tag Deletion
You can delete the declared tag. If tag is deleted, some error may occur at the place where the tag is applied before.
[Procedures]
(1) After selecting [Tag 1] from a project screen, select or double-click [View]-[Properties] menu.
(2) Select [Default] tag group.
(3) Select the tag to be deleted from tag screen.
(4) Select [Edit]-[Delete] menu or press Delete key.
(5) The tag will be deleted.
Notice
(1) If you select tag name cell and delete the tag, the tag will be deleted.
(2) If you select tag type and delete the tag, the type will be deleted and it will become bit type. Tag must have the type
all the time so it is changed into bit type or nochanges.
(3) If you select tag device and delete the tag, only device will be deleted.
(4) If you select tag comment and delete the tag, only comment will be deleted.
Chap.5 Tag
5-9
5.4 Tag Revision
You can change the name, device, comment, type of the declared tag.
[Procedures]
(1) After selecting [Tag 1] from a project screen, select or double-click [View]-[Registration Information] menu.
(2) Select [Default] tag group.
(3) Select the tag to be changed from tag screen.
(4) Input the revised details.
Notice
(1) The tag name must exist.
(2) The tag name can not be overlapped within the same tag screen(tag 1 tag)
(3) The overlapped tag name can be declared between tag 1 and tag 2 screen.
Chap.5 Tag
5-10
5.5 Tag Copy/Paste
[Procedures]
(1) After selecting [Tag 1] from a project screen, select or double-click [View]-[Registration Information] menu.
(2) Select the [Default] tag group.
(3) Select the tag to be copied at tag screen.
(4) After selecting [Edit]-[Copy] menu, copy the tag to a clipboard.
(5) Move to the position to for Paste.
(6) Select [Edition]-[Paste] menu and paste it.
Notice
(1) When pasting tag name, the name of copy is displayed as “Original name_Number” to avoid overlapped name.
(2) The Copy function of tag screen acts as copying sting. Namely, only selected cell is copied.
Chap.5 Tag
5-11
5.6 Tag Cut/Paste
[Procedures]
(1) After selecting [Tag 1] from a project screen, select or double-click [View]-[Properties] menu.
(2) Select the [Default] tag group.
(3) Select the tag to be cut at tag screen.
(4) After selecting [Edit]-[Cut] menu, copy the tag to a clipboard and delete it.
(5) Move to the position to for Paste.
(6) Select [Edit]-[Paste] menu and paste it.
Notice
(1) Tag Cut/Paste operation is the same as Tag Deletion-Tag Copy/Paste.
Chap.5 Tag
5-12
5.7 Tag Auto-Filling
Tag screen has the Auto-Filling function just as Excel. Through this function, you can promptly declare tag that has continuous
device address with a similar name.
[Procedures]
(1) After selecting [Tag 1] from a project screen, select or double-click [View]-[Registration Information] menu.
(2) Select the [Basic] tag group.
(3) Select the right below corner of the cell for Auto-Filling at tag screen and make the shape of mouse cursor as
below.
(4) After clicking the right lower part of selected cell, drag it down.
(5) After moving to the position where Auto-Filling mode is terminated, put away the mouse.
(6) Then, Auto-Filling process is completed.
Chap.5 Tag
5-13
Notice
(1) For Name Auto-Filling column, it increases as “Selected Tag Name+ Number to avoid overlapped tag name.
(2) Type Auto-Filling column does not increase.
(3) In the terms of Device ColumnAuto-Filling, the address increases automatically.
(4) In the terms of Comment Column Auto-Filling, it increases as “Selected Comment +Number”.However, when you
execute Auto-Filling with pressing Ctrl key, it does not increase and filled with the same comment.
(5) You can select several horizontal rows for Auto-Filling.
(6) In the case of Auto-Filling to the upper direction, it decreases as “Selected tag - number”.
Chap.5 Tag
5-14
5.8 Tag Group
For tag group, you can declare tag by collecting the related tag group. It is also required for device communication by tag group.
[The kinds of Tag Group]
Tag Group Description
Default Tag Group(a) The tag group is added basically when node is added to XP-Manager. The group can not
be deleted but tag declaration is allowable.
System Tag Group(b)
The tag group is added basically when node is added to XP-Manager. The group can not
be deleted and it is the system tag declared basically at XGT Panel. In this case, Tag
Declaration/Deletion is not available.
User’s declared tag group
(c)
The tag group is added by a user and a user can delete it or change its name. Tag
Declaration/Deletion process is also available.
Notice
(1) Tag group declaration is not limited in the number.
(2) For basic tag group, system tag group, you can not delete them or not change their name.
(a)
(b)
(c)
Chap.5 Tag
5-15
5.9 Tag Group Declaration
You can add tag group.
[Procedures]
(1) After selecting [Tag 1] from a project screen, select or double-click [View]-[Properties] menu.
(2) Select the light tag group screen.
(3) Click the right mouse button at tag screen and select [New Group] of context menu.
(4) Click the right mouse button at tag group screen and select [New Group] of context menu.
(5) It is added under the name of “New Group” and you can change the name.
Notice
(1) The overlapped name of tag group can not be declared.
(2) You can apply special characters to tag group name.
(3) You can change the name by selecting the selected tag group at tag group screen or selecting [Change Name]
of context menu.
Chap.5 Tag
5-16
5.10 Deleting Tag Group
You can delete the added tag group.
[Procedures]
(1) After selecting [Tag 1] from a project screen, select or double-click [View]-[Registration Information] menu.
(2) Select the light tag group screen.
(3) Select the tag group to be deleted and apply [Delete Group] of context menu.
(4) Then, the tag group is deleted.
Notice
(1) When tag group is deleted, all tags of tag group are deleted.
Chap.5 Tag
5-17
5.11 Tag Group Copy/Paste
You can re-use the added tag through Copy/Paste.
[Procedures]
(1) After selecting [Tag 1] from a project screen, select or double-click [View]-[Registration Information] menu.
(2) Select the light tag group screen.
(3) Select the tag group to be copied and apply [Copy] of context menu.
(4) Select tag group screen and select [Paste] of context menu.
(5) Then, the tag group is pasted with the tag of tag group.
Notice
(1) When tag group is copied, all tags of groups will be also copied.
(2) When pasting tag group, it is displayed as “Name_Number” to avoid overlapped name.
(3) When pasting tag, it is displayed as “Name_Number”.

Chap. 6 Device Communication
6-1
Chap. 6 Device Communication
6.1 Device Communication Screen
[Procedures]
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Properties].
[Screen]
[Description on a screen]
Item Description
Using row(a) If you activate using row, device communication will work. If you undo activation for
non-used device communication and download it, device communication will not work.
Device Communication
Screen Name (b)
It indicates the node name and device communication screen.
Device Row(c) It indicates the name, type, quantity of operated device.
Action) It indicates the operation mode.
Target Device Row(e) It displays the target device list.
No.(f) It indicates the No. of device communication from 1 to 64.
(a) (b) (c) (d) (e)
(f)
Chap. 6 Device Communication
6-2
6.2 Editing Device Communication
6.2.1 Reading Device
You can perform Reading Device.
[Procedures]
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Properties]
(2) After selecting the row to be edited, select or double-click [View]-[Properties]
(3) Select Reading mode for operation.
(4) Select operating device type and input the device.
(5) Select the target node with the same type as operating device and input the device.
(6) Press OK button and close the dialog box.
[Dialog Box]

(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
(j) (k) (l)
(r) (q) (p) (o) (n) (m)
Chap. 6 Device Communication
6-3
[Description on a dialog box]
Item Description
Action (a) It selects operation of device communication. Reading from other node,
Writing to other node is available.
Action Device(b) Under Reading mode, the device saves the data read from other node.
Under Writing mode, the data of this device can be written to other node.
Type(c)
It is operating device type. In case that operating device type is bit, the target device
should be all bit. In case that operating device is 16bit, the target device should be
16bit and if the operating device is 32bit, the target device should be 32 bit.
Name((d) You can input device name by using device selection button.
The number of devices(e) You can input the number of continuous devices
Communication response
setting (f)
It checks whether device communication works successfully or not. Under Reading
mode, Checking Communication Response option is active all the time.
Timeout (g) You can input timeout value for the case that device communication fails.
The maximum limit is 10 seconds.
Retrial(h) You can input the frequency of retrying communication when timeout occurs.
Save Status (i) The device is to dace the operation status of device communication.
Transmit tag group at once
(j)
When tag group is applied to operating device, the option is to transmit the
device of tag group at once.
OK(k) It saves the details of a dialog box and closes it.
Cancel(l) It closes the dialog box without saving dialog box details.
Down(m) It moves the selected target device to the lower direction.
Up(n) It moves the selected target device to the upper direction.
Delete (o) It deletes the selected device.
Target Device(p) It can input the target device.
Type(q) It selects the target device type.
Node(r) It selects the target node.
Notice
(1) For Reading mode, you can designate only one target device.
(2) For Writing mode, you can designate the target device up to 1024EA.
(3) The type of operating device should be the same as the type of target device.
(4) In Reading mode, operating device is Read Only device, error may occur.
6.2.2 Writing Device
[Procedures]
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Properties].
(2) After selecting the row to be edited, select or double-click [View]-[Properties].
Chap. 6 Device Communication
6-4
(3) Select Writing mode for operation.
(4) Select action device type and input the device.
(5) Select the target node with the same type as operating device and input the device.
(6) Press OK button and close the dialog box.
[Dialog Box]
Notice
(1) If too many device communications or target devices are designated, it may deteriorate the performance of XGT Panel.
6.2.3 Using Tag Group
You can designate tag group with action device of device communication and it is useful to send communication operations as
structured data.
[Procedures]
Chap. 6 Device Communication
6-5
(1) Open tag screen.
(2) Add the tag group.
(3) Add the tag.
(4) After selecting [Device Communication] at a project screen, select or double-click [View]-[Properties].
(5) After selecting the row to be edited, select or double-click [View]-[Properties].
(6) Select device selection button.
Chap. 6 Device Communication
6-6
(7) Activate the tag and Selecting Tag Group menu.

(8) After selecting tag group from tag group list and press OK button.
Chap. 6 Device Communication
6-7
(9) After selecting operating device and target device as tag group, press OK button.
Notice
(1) If action device is tag group, the target device that has the same structure should be added.
(2) If action device is designated as tag group, you cannot set the device type and quantity.
(3) If the tag group of action device has different structure from the target device’s tag group, error may occur.
Chap. 6 Device Communication
6-8
6.3 Deleting Device Communication
[Procedures]
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Properties].
(2) Select the edge of row to be deleted.
(3) Select [Edit]-[Delete] menu.
Notice
(1) If you select several rows and delete it, all selected items will be deleted.
Chap. 6 Device Communication
6-9
6.4 Device Communication Copy/Paste
[Procedures]
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Registration
Information].
(2) Select the edge of row to be copied and select [Edition]-[Copy] menu.
(3) Move to the cell to be pasted and select [Edition]-[Paste] menu to paste it.
Notice
(1) You can paste the copied details to other XP-Manager.
(2) After Paste, the node name or device name may not be shown since the copied node name does not exist at the
pasted project. In this case, re-edit the pasted row to delete error.
* After Paste, select the screen where error occurred, target node, delete error.
Chap. 6 Device Communication
6-10
6.5 Device Communication Cut/Paste
[Procedures]
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Properties].
(2) Select the edge of row to be cut and select [Edit]-[Cut] menu.
(3) The selected row is deleted.
(4) Move to the cell to be pasted and select [Edition]-[Paste] to paste it.
Notice
(1) Cut is the same as the Delete function after Copy.
Chap. 6 Device Communication
6-11
6.6 Device Communication Drag & Drop
[Procedures]
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Properties].
(2) Select the edge of row to be dragged and click the left mouse button.
(3) Put the mouse to the position to be dragged and out it away.
(4) You can see that the selected row is moved.
Notice
(1) The Drag & Drop function at the identical screen is the same as Copy/Paste.
(2) The Drag & Drop function to other screen is the same as Copy/Paste.
(3) If you drop with pressing Ctrl button, Copy/Paste function at the same screen is available.
Chap. 6 Device Communication
6-12
6.7 Delete Device Communication
[Procedures]
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Properties].
(2) Select the row to be deleted.
(3) Select [Edition]-[Delete] menu and delete it.
(4) Select [Edition]-[Undo] menu.
(5) It returns to the previous status before edition.
Notice
(1) You need the previous edition history to Undo Edition.
(2) Redo Edition is not limited in the quantity.
(3) You can Undo Edition for all functions.
Chap. 6 Device Communication
6-13
6.8 Redo Device Communication
[Procedures]
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Properties].
(2) Select the row to be deleted.
(3) Select [Edit]-[Delete] menu and delete it.
(4) Select [Edit]-[Undo] menu.
(5) Then, it returns to the previous status before edition.
(6) Select [Edit]-[Redo] menu.
(7) Then, selected row is deleted again.
Notice
(1) Redo Edition is not limited in the quantity.
(2) You need the previous edition history to Redo Edition.
Chap. 6 Device Communication
6-14
6.9 Device Communication Print Preview
[Procedures]
(1) After selecting [Device Communication] at a project screen, select or double-click [View]-[Registration
Information].
(2) Select Device Communication screen.
(3) Select [Project]-[Print Preview] menu.
[Screen]
[Description on a screen]
Item Description
Print(a) It prints the current screen.
Next Page (b) It previews the next screen.
Previous Page(c) It previews the previous screen.
Two Pages(d) It previews two pages per screen.
Zoom In(e) It expands the current screen to full size.
Zoom Out(f) It reduces the current Preview Screen.
Close(g) It closes the Preview Screen and moves to the Edition Screen.
Screen(h) It previews the current screen.
Notice
(1) It is printed as Preview Screen.
(2) Through Preview Screen, you can adjust the screen not to be cut with the width of row.
(3) Edition is not available at Preview Screen.
(a) (b) (c) (d) (e) (f) (g)
(h)
Chap. 6 Device Communication
6-15
6.10 Device Communication Print Preview
[Procedures]
(1) After selecting [Device Communication] at a project screen, select or double-click [View]-[Properties].
(2) Select Device Communication screen.
(3) Select [Project]-[Print] menu.
(4) The Print Dialog Box will be shown as below.
(5) Then, press [OK] button to print it.
Notice
(1) The above dialog box may be different depending on Windows version.

Chap.7 Work
7-1
Chapter 7 Work
7.1 Work Window
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
[Window]

[Window Description]
Item Description
Use(a) Check a row to activate the work. The work is not activated, if the check is cancelled and
downloaded.
Work Window Name(b) Its node name is displayed and it is confirmed that it is the work window.
Work(c) The work profile is displayed.
Action(d) Its action mode and image are displayed.
Detail(e) The work’s detailed description is specified.
Number(f) The work number is displayed. Number 0 through 63.
Note
(1) The work window can be edited only onXP-server node.
(2) In case of “Various Work using Excel template file”, various detailed actions are displayed.
(a) (b) (c) (d) (e)
(f)
Chap.7 Work
7-2
7.2 Edit
7.2.1 Various Work using Excel template file
Various actions can be performed with Excel files.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to edit and then select Menu [View]-[Properties] or double click.
(3) Select a work type from [Various Work using Excel template file].
(4) Select [template file].
(5) Select [Edit template file] and edit the work on Excel.
(6) Enter [Read Output Folder] and [Read Output File].
(7) Press the “OK” button to close the dialog box.
[Dialog Box]
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h) (i)
(j)
Chap.7 Work
7-3
[Dialog Box Description]
Item Description
Work type(a) Select a work type.
Template file(b) Enter the template file name. Enter the file path.
Read output folder(c) Designate the Excel file location to which XP-Server in action will be saved.
Read output file(d) Designate the Excel file name in which XP-Server in action will be saved. If a field is used,
the file name will be dynamically changed.
Save method(e) Designate whether to add data only to the end of the file or to create a new file when XPServer in action saves a file.
Write source file(f) Enter the file name in which the original data are saved when XP-Server in action writes
data. Enter the file path.
Status device (g) Action state of this work is saved.
OK(h) Close the dialog box with saving the content in it.
Cancel(i) Close the dialog box without saving the content in it.
Edit template file(j) Execute Microsoft Excel to open the template file.
Note
(1) For further information on the editing on Excel, see “Chapter 15, Excel Work”.
(2) If a field is used for the file name, the file name will be dynamically changed. It is available to use both field and string
together. Fields are as below:
Field Name Action Example (when it is 2010-12-14-05-30-30)
%Y Save the file name in the current year when saving Year%Y.csv Year2010.csv
%M Save the file name in the current month when saving. %M_Month.xls 12_Month.xls
%D Save the file name in the current day when saving Day_%D_out.txt Day_14_out.txt
%h Save the file name in the current time when saving. Time_%h.csv Time_5.csv
%m Save the file name in the current minute when
saving.
_%m_minute.xls _30_minute.xls
%s Save the file name in the current second when
saving
Second-%s_log.txt Second-30_log.txt
(3) Depending on Save Method Mode, one file can save data. But, if a field is used for the file name, data can be saved in
other files.
Save Method Action
Create a new file A new file with the designated file name is created whenever data are read
and saved in a file. If there is an existing file with the same file name, data
will be updated.
Append data to end of file When data is read and saved in a file, a new file will be created if there is no
file and only data contents will be added to the end of the work if there is
already a file.
(4) For the Status Devices, enter writable word devices. When the work is performed, status information such as normality or
error is displayed.
(5) Special characters cannot be used for file names. ( / : * ? < > |)
(6) Special characters cannot be used for file names. (/ : * ? < > |)
Chap.7 Work
7-4
7.2.2 XP-Server Recipe – CSV File
Data in CSV file can be written with the subject node.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to edit and then select Menu [View]-[Properties] or double click.
(3) Select [XP-Server Recipe – CSV File] for Work Type.
(4) Enter [File].
(5) Enter information on the subject node and device.
(6) Press the OK button to close the dialog box.
[Dialog Box]
[Dialog Box Description]
Item Description
File(a) Enter the name of the CSV file that will be the source of the writing data. Enter the path.
Line number(b) Write the data in the subject node on a particular line in the CSV File.
Line number device(c) Available to change the CSV file’s line number dynamically.
Node(d) Obtain the CSV file’s line number with this node’s device value.
Device(e) Obtain the CSV file’s line number with the readable word device value.
Subject Node(f) Designate a target node.
Type(g) Designate a type of device.
Count(h) Enter the number of consecutive devices.
Device(i) Enter a device subject to writing.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
Chap.7 Work
7-5
Note
(1) The LineNumber Device is a readable word device.
(2) For detailed action description on “XP-Server’s Recipe –CSV File”, refer to Chapter 2 of “Chapter 16 Work Operation”.
(3) Special characters cannot be used for file names. (/ : * ? < > |)
7.2.3 XP-Server Logging– CSV File
The data read from the node can be saved in a CSV file.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to edit and then select Menu [View]-[Properties] or double click.
(3) Select [XP-Server Logging– CSV File] for Work Type.
(4) Enter [Folder] and [File].
(5) Enter information on the subject node and device.
(6) Press the OK button to close the dialog box.
[Dialog Box]
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
Chap.7 Work
7-6
[Dialog Box Description]
Item Description
Folder(a) Enter the name of the folder in which a CSV file will be saved. Enter the relative path.
File(b) Enter a CSV file name.
Save(c) Select an option to save data.
Time(d) Select an option to display time when saving data.
Target Node(e) Designate a subject node.
Type(f) Designate a type of device.
Count(g) Enter the number of consecutive devices.
Device(h) Enter a device subject to reading.
Note
(1) If option “Create new file”is designated without using a field for the file name, only one file will be saved.
(2) For detailed action description on “XP-Server Logging –CSV File”, refer to Chapter 3 of “Chapter 16 Work Operation”.
(3) Special characters cannot be used for file names. ( / : * ? < > |)
(4) Special characters cannot be used for file names. (/ : * ? < > |)
7.2.4 XP-Server Logging– Database
The data read from the node can be saved in database.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to edit and then select Menu [View]-[Properties] or double click.
(3) Select [XP-Server Logging– Database] for Work Type.
(4) Enter [Server Type] and [File Name].
(5) Press [Settings to save device in database] to enter Database Table, Field and Device to be saved
(6) Press the OK button to close the dialog box.
Chap.7 Work
7-7
[Dialog Box] – In case that the server type is Microsoft Office Access,
[Dialog Box] – In case that the server type is SQL Server
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
Chap.7 Work
7-8
[Dialog Box Description]
Item Description
Server Type(a) Select a Database Server Type.
Driver(b) Select a driver to access to the server.
File Name(c) Enter a Microsoft Office Access file. Enter the entire file paths.
Settings to save device in
database(d)
Enter a device to be saved in the database. Enter Database Table, Field, Subject Node
and Device to be saved.
Server Name or IP
Address(e)
Enter the computer name or IP address in which SQL Server is located.
Database Name(f) Enter the database name.
Log-in Name(g) Enter the log-in name to access to SQL Server.
Log-in Password(h) Enter log-in password.
Connection Time Out(i) Enter the Connection Time-Out time when connecting with SQL Server.
Note
(1) If option “Create new file”is designated without using a field for the file name, only one file will be saved.
(2) For detailed action description on “XP-Server Logging- Database” refer to Chapter 4 of “Chapter 16 Work Operation.”
(3) Special characters cannot be used for file names. ( / : * ? < > |)
[Dialog Box] – Settings to save device in database
(a)
(b)
(c)
(d)
(e)
(f)
Chap.7 Work
7-9
[Dialog Box Description]
Item Description
Table Name(a) Enter a table name in the database.
Field(b) Enter a field in the table.
Node(c) Enter the subject node name.
Type(d) Enter a type of the device.
Device(e) Enter a device subject to reading.
Delete(f) Delete the selected item.
7.2.5 Read/Write XGT Panel’s Recipe – CSV File
XGT Panel’s Recipe can be read and written in CSV File.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to edit and then select Menu [View]-[Properties] or double click.
(3) Select [Read/Write XGT Panel’s Recipe – CSV file] for Work Type.
(4) Enter [File].
(5) Enter information on the subject node and recipe.
(6) Press the OK button to close the dialog box.
[Dialog Box]
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(i)
Chap.7 Work
7-10
[Dialog Box Description]
Item Description
Action(a) Designate read or write action.
Folder(b) Enter the folder name. Enter the relative path.
File(c) Enter the file name.
Target Node(d) Enter the subject XGT panel node name.
Recipe Type(e) Select a type of the recipe.
Recipe No.(f) Enter recipe number.
Recipe No.Device(g) Available to change the recipe number dynamically.
Node(h) Obtain the recipe number with this node’s device value.
Device(i) Obtain the recipe number with the readable word device value.
Note
(1) Recipe No. Device is a readable word device.
(2) For detailed action description on “Read/Write XGT Panel’s Recipe –CSV File”, refer to Chapter 5 of “Chapter 16 Work
Operation”.
(3) To write right data, use CSV File saved through Read action.
(4) For subject node, only XGT Panel Node is available. XP-Server Node is not available.
(5) When performing “Write” action, if file is on PC, it downloads the relevant file to XP-Server.
7.2.6 Read logging data on XGT Panel ‘s NVRAM – CSV File
The logging saved in XGT Panel’s NVRAM can be read in CSV File.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to edit and then select Menu [View]-[Properties] or double click.
(3) Select [Read NVRAM logging on XGT Panel– CSV File] for Work Type.
(4) Enter [Folder] and [File].
(5) Enter information on the subject node and logging.
(6) Press the OK button to close the dialog box.
Chap.7 Work
7-11
[Dialog Box]
[Dialog Box Description]
Item Description
Folder(a) Enter the folder name. Enter the relative path.
File(b) Enter the file name. Enter the relative path.
Target Node(c) Enter the subject XGT panel node name.
Logging Number(d) Enter the logging number.
Logging Number Device(e) Available to change the logging number dynamically.
Node(f) Obtain the logging number with this node’s device value.
Device(g) Obtain the logging number with the readable word device value.
Note
(1) Logging Number Device is a readable word device.
(2) For detailed action description on “Read logging data on XGT Panel’s NVRAM –CSV File,” refer to Chapter 6 of “Chapter
16 Work Operation”.
(3) For subject node, only XGT Panel Node is available. XP-Server Node is not available.
(4) Special characters cannot be used for file names. ( / : * ? < > |)
(5) Special characters cannot be used for file names. (/ : * ? < > |)
(a)
(b)
(c)
(d)
(e)
(f)
(g)
Chap.7 Work
7-12
7.2.7 Read Alarm data in XGT Panel’s NVRAM – Unicode Text File
Logging saved in XGT Panel’s NVRAM can be read in CSV File.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to edit and then select Menu [View]-[Properties] or double click.
(3) Select [Read Alarm data in XGT Panel’s NVRAM – Unicode Text File] for Work Type.
(4) Enter [Folder] and [File].
(5) Enter information on the subject node and alarm.
(6) Press the OK button to close the dialog box.
[Dialog Box]
[Dialog Box Description]
Item Description
Folder(a) Enter the folder name. Enter the relative path.
File(b) Enter the file name. Enter the relative path.
Target Node(c) Enter the subject XGT panel node name.
Alarm Group Number(d) Enter the alarm group number.
Alarm Group Number
Device(e)
Available to change the alarm group number dynamically.
Node(f) Obtain the alarm group number with this node’s device value.
Device(g) Obtain the alarm group number with the readable word device value.
(a)
(b)
(c)
(d)
(e)
(f)
(g)
Chap.7 Work
7-13
Note
(1) The Alarm Group Number Device is a readable word device.
(2) For detailed action description on “Read Alarm data inXGT Panel’s NVRAM–Unicode Text File”, refer to Chapter 7 of
“Chapter 16 Work Operation”.
(3) For subject node, only XGT Panel Node is available. XP-Server Node is not available.
(4) When directly entering alarm group number, enter XP-Builder’s alarm group ID. This function is compatible with XP-Builder
version 1.24 or higher.
(5) Special characters cannot be used for file names. ( / : * ? < > |)
(6) Special characters cannot be used for file names. (/ : * ? < > |)
7.2.8 Read XGT Panel screen-shot file
It is possible to capture XGT Panel’s current screen and read it in a bitmap file.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]- [Properties] or double click.
(2) Select a row to edit and then select Menu [View]- [Properties] or double click.
(3) Select [Read XGT Panel screen-shot file] for Work Type.
(4) Enter [Output Folder] and [Output File].
(5) Enter the subject node.
(6) Press the OK button to close the dialog box.
Chap.7 Work
7-14
[Dialog Box]
[Dialog Box Description]
Item Description
Output Folder(a) Enter the folder name. Enter the relative path.
Output File(b) Enter the file name. Enter the relative path.
Target Node(c) Enter the subject XGT panel node name.
Note
(1) For detailed action description on “Read XGT Panel screen-shot file,” refer to Chapter 8 of “Chapter 16 Work Operation.”
(2) For subject node, only XGT Panel Node is available. XP-Server Node is not available.
(3) Special characters cannot be used for file names. ( / : * ? < > |)
(4) Special characters cannot be used for file names. (/ : * ? < > |)
(5) Function ‘Capture Screen’ may take different time depending on machine types. For XP30, it takes less than 3 seconds, for
XP50 or XP70, less than 5 seconds and for XP90, less than 10 second. Therefore, it is essential to appropriately define
time-out time of XP-Server in which ‘Read XGT Pane screen-shot file ’ is defined in order to have normal operation.
(a)
(b)
(c)
Chap.7 Work
7-15
7.2.9 Send E-mail on PC
E-mail can be sent.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to edit and then select Menu [View]-[Properties] or double click.
(3) Select [Send E-mail on PC] for Work Type.
(4) Enter E-mail information.
(5) Press the OK button to close the dialog box.
[Dialog Box]
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
(k)
(j)
(i)
Chap.7 Work
7-16
[Dialog Box Description]
Item Description
IP Address or SMTP Server Name
(a)
Enter the IP address of the SMTP Server or the server name.
Use SSL/TLS (b) Data is encrypted when they are sent to the mail server.
My SMTP server requires
authentication (c)
Unless non-account mail service of the Intranet’s SMTP Server (Anonymous
SMTP is used, the user’s information needs to be authenticated.
User account(d) If [My SMTP server requires authentication] is checked, Enter the user’s account.
E-mail address (e) Set a sender’s mail address. Use ‘;’to set multiple senders. The same mail will be
set to all of the registered persons.
Sender’s E-mail address(f) Set a sender. Set a mail account.
Title(g) Enter the mail title.
Message(h) Enter the mail content.
Password (i) If [My SMTP server requires authentication] is checked, Enter the user’s password.
Validate server certificate (j) Check the certificate of SMTP Server.
SMTP Port No.(k) Enter the number of SMTP Server’s port. If non-account mail service of the
Intranet’s SMTP Server (Anonymous SMTP) is used, the port number will be 25.
Note
(1) For detailed action description on XP-Server’s “Send E-mail on PC,” refer to Chapter 9 of “Chapter 16 Work Operation.”
(2) If User Authentication is not used (Anonymous SMTP), SMTP Server shall be on the same Intranet network with XGT
Panel. In this case, the port number shall be designated as 25, the basic port of Anonymous SMTP service.
(3) If URL is used instead of directly entering the server’s IP, DNS Server’s IP shall be set from the starting Menu.
(4) The sending mail is coded in unicode.
7.2.10 Start application
Memo board, Paint, Excel and other application programs can be executed on PC.
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to edit and then select Menu [View]-[Properties] or double click.
(3) Select [Start application] for Work Type.
(4) Enter [File Name].
(5) Enter a subject node.
(6) Press the OK button to close the dialog box.
Chap.7 Work
7-17
[Dialog Box]
[Dialog Box Description]
Item Description
File Name(a) Enter the program name. Enter the entire file paths.
Start option (b) Enter an option when the program starts executing.
Start a new instance of
application (c)
Execute a new program while the same program is executed. More than two
programs can be executed at the same time.
Note
(1) For detailed action description on XP-Server’s “Start application,” refer to Chapter 10 of “Chapter 16 Work Operation.”
(2) Special characters cannot be used for file names. ( / : * ? < > |)
(a)
(b)
(c)
Chap.7 Work
7-18
7.3 Delete
[Sequence]
(1) Double click [Work] on the project window
(2) Select a row to delete
(3) Select Menu [Edit]-[Delete].
Note
(1) If several rows are selected, all of them will be deleted at the same time.
(2) Sub-items of Item “Various Works using Excel template file on PC” cannot be deleted. To delete them, press [Edit Excel
TemplateFile] button to execute Excel.
Chap.7 Work
7-19
7.4 Copy/Paste
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to copy and select Menu [Edit]-[Copy].
(3) After moving to the cell to paste, select Menu [Edit]-[Paste] to paste.
Note
(1) Any copied content can be pasted in other XP-Manager.
(2) Node Name or Device Name may become invisible after being pasted. Such a case may happen because there is no
project to which the copied node name is pasted. To resolve this problem, edit the row subject to being pasted.
Chap.7 Work
7-20
7.5 Cut/Paste
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to cut and select Menu [Edit]-[Cut].
(3) The selected row will be deleted.
(4) After moving to the cell to paste, select Menu [Edit]-[Paste] to paste.
Note
(1) ‘Cut’ is equivalent to ‘Delete after copying.’
Chap.7 Work
7-21
7.6 Drag & Drop
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select an edge of the row to drag and press the left button of the mouse.
(3) After moving to the location to drop, release the mouse.
(4) The previously selected row will be moved.
Note
(1) Function Drag & Drop in the same window equals to Function Cut/Paste.
(2) Function Drag & Drop in the different windows equals to Function Copy/Paste.
(3) When dropping, press the Ctrl button and drop to have the same function with Copy/Paste even in the same window.
Chap.7 Work
7-22
7.7 Cancel edition
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to delete.
(3) Select Menu [Edit]-[delete] to delete.
(4) Select Menu [Edit]-[Undo].
(5) The work is returned to the one before being edited.
Note
(1) Cancelling edition is available only when edition is done previously.
(2) There is no limit to the number of cancelling edition.
(3) All editions will be cancelled.
Chap.7 Work
7-23
7.8 Redo
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a row to delete.
(3) Select Menu [Edit]-[delete] to delete.
(4) Select Menu [Edit]-[Undo].
(5) The work is returned to the one before being edited.
(6) Select Menu [Edit]-[Redo].
(7) The selected row is redeleted.
Note
(1) There is no limit to the number of redoing edition.
(2) Redoing edition is available only when the previous edition is cancelled.
7.9 Print Preview
[Sequence]
Chap.7 Work
7-24
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a work window.
(3) Select Menu [Project]-[Print Preview].
[Screen]
(a) (b (c) (d) (e) (f) (g)
(h)
Chap.7 Work
7-25
[Screen Description]
Item Description
Print(a) The current window will be printed.
Next(b) The next window will be previewed.
Previous(c) The previous window will be previewed.
Two Pages(d) Two pages will be previewed on a screen.
Zoom In(e) The current preview widow will be zoomed in.
Zoom Out(f) The current preview widow will be zoomed out.
Close(g) The current preview widow will be closed to move to the edit window.
Screen(h) The current screen will be previewed.
Note
(1) It is printed as seen on the preview screen.
(2) Ensure any part of the screen is not cut through Print Preview and adjust the width of the row.
(3) Editing is not allowed in the preview screen mode.
Chap.7 Work
7-26
7.10 Print
[Sequence]
(1) Select [Work] from the project window and then select Menu [View]-[Properties] or double click.
(2) Select a work window.
(3) Select Menu [Project]-[Print].
(4) The print dialog box appears as below
(5) Press the [OK] button to print.
Note
(1) The above print dialog box may vary depending on the computer’s window version.

Chap.8 Trigger Condition
8-1
Chap. 8 Trigger Condition
8.1 Description on the screen of Trigger Condition
[Procedures]
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Registration Information]
menu.
[Screen]
[Description on a screen]
Item Description
Using row (a) Trigger condition does not work until using row is checked.
Trigger condition screen name
(b)
It indicates the node name and trigger condition screen.
Trigger Condition row(c) It describes trigger condition.
Full Screen Button (d)
It is displayed when there is the device communication connected to trigger
condition. Every time that you press the button, connected device
communication is expanded or reduced.
Connected device
communication row (e)
It indicates the connected device communication list.
No.(f) It indicates the number of trigger condition from 1 to 64.
(a) (b) (c) (d) (e)
(f)
Chap.8 Trigger Condition
8-2
8.2 Editing Trigger Condition
Trigger is to provide the condition for device communication under XP Link communication of XGT Panel. Every time trigger is
configured, device communication connected to trigger is available. There are bit, word, time, system triggers.
8.2.1 Editing Bit Trigger
You can configure trigger with bit device condition.
[Procedures]
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) After selecting the row to be edited, select or double-click [View]-[Properties].
(3) Select the bit trigger.
(4) Input the bit device.
(5) Input bit condition.
(6) Press OK button to close a dialog box.
[Dialog Box]

(a) (b) (c) (d)
(e)
(f)
(q)
(h)
(g)
(i)
(j)
(p)
(o)
(n) (m) (k) (l)
Chap.8 Trigger Condition
8-3
[Description on a dialog box]
Item Description
Bit Trigger(a) It configures the trigger on condition of bit device condition.
Word Trigger(b) It configures the trigger on condition of word device condition
Time Trigger(c) It configures the trigger at a specific time.
System Trigger (d) It configures the trigger depending on operation status of XGT Panel.
The number of Triggers(e) You can set the number of triggers up to 4 EA.
Current Trigger(f) You can select the trigger for current edition among 4 triggers.
Frequency, Once(g) It configures trigger once when trigger condition is fulfilled.
Frequency, Continuously (h) It configures trigger even after trigger condition is fulfilled.
Operation Condition(i) For complex trigger that has two or more, it can configure trigger with operation
condition between triggers.
Specific Interval(j) It configures trigger at certain interval after trigger is configured. However, trigger
condition is not fulfilled, trigger is not configured.
During specific time (k) It configures continuously trigger at a certain time.
Time Setting (l) You can input time value.
OK(m) It saves the details of a dialog box and closes it.
Cancel(n) It closes the dialog box without saving the details of a dialog box.
Device (o) You can input bit device.
Bit Condition (p)
You can select bit condition.
Bit On
Bit Off
Bit Reversal
During Bit On
During Bit Off
Bit changes after meeting
condition (q)
When bit device condition is [Bit On] or [Bit Off], it reverses the bit device value after
conditions are fulfilled.
Notice
(1) Read only device can not be designated as bit condition device.
(2) After the condition is fulfilled, bit reversal (q) is active only when bit condition is [Bit On] or [Bit Off].
(3) Time Setting (l) is active only when Frequency Continue (h) is applied.
Chap.8 Trigger Condition
8-4
8.2.2 Editing Word Trigger
You can configure trigger with bit device condition.
[Procedures]
(1) [After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) After selecting the row to be edited, select or double-click [View]-[Properties].
(3) Select the word trigger.
(4) Input the word device.
(5) Input word condition.
(6) In case that word condition is [When meeting condition] or [During meeting condition], input the condition.
(7) Press OK button to close a dialog box.
[Dialog Box]
(a) (b)
(e)
(d) (c)
(f) (g)
Chap.8 Trigger Condition
8-5
[Description on a dialog box]
Item Description
Word Trigger (a) It configures trigger on condition of word device.
Device (b) You can input word device.
Type(c) It selects device type.
Word Condition(d)
You can select word condition.
When condition expression
is fulfilled
Condition Expression: 0 < HW0000
While condition expression
is fulfilled
Condition Expression: 0 < HW0000 < 100
When the value is changed
Condition Expression (e) You can input condition expression.
OK(f) It saves the details of a dialog box and closes it.
Cancel (g) It closes the dialog box without saving the details of a dialog box.
Notice
(1) Read Only device can not be designated as word condition device.
(2) Condition expression (e) is active only when word condition is [When meeting condition] or [During meeting condition].
8.2.3 Editing Time Trigger
You can configure trigger at a specific time.
[Procedures]
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) After selecting the row to be edited, select or double-click [View]-[Properties].
Chap.8 Trigger Condition
8-6
(3) Select time trigger.
(4) Set the specific time or repeating time.
(5) Press OK button to close the dialog box.
[Dialog Box]
[Description on a dialog box]
Item Description
Time Trigger(a) It configures the trigger at a specific or certain time.
Time Conditions(b) You can input every year/every month/every week/every hour/every minute
with time conditions.
OK (c) It saves the details of a dialog box and closes it.
Cancel (d) It closes the dialog box without saving the details of a dialog box.
(a) (b)
(c) (d)
Chap.8 Trigger Condition
8-7
8.2.4 Editing System Trigger
[Procedures]
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) After selecting the row to be edited, select or double-click [View]-[Properties].
(3) Select system trigger.
(4) Establish the conditions for system trigger.
(5) Press OK button to close a dialog box.
[Dialog Box]
[Description on a dialog box]
Item Description
System Trigger (a) It configures the trigger with the event that can occur at XGT Panel only.
Condition(b) It selects the conditions for system event.
OK(c) It saves the details of a dialog box and closes it.
Cancel (d) It closes the dialog box without saving the details of a dialog box.
(a) (b)
(d) (c)
Chap.8 Trigger Condition
8-8
8.2.5 Complex Trigger
When two triggers or more are designated, it is called complex trigger.
[Procedures]
(1) [After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) After selecting the row to be edited, select or double-click [View]-[Properties].
(3) Select two complex triggers.
(4) Select [Trigger 1] and set the details.
Chap.8 Trigger Condition
8-9
(5) Select [Trigger 2] and set the details.
(6) Select operation conditions.
(7) Press OK button to close a dialog box.
Notice
(1) In the case of the given example, conditions are [When monitor stars] and bit [HX0000 is On].
(2) You can designate the complex triggers up to 4 EA.
(3) While operation condition AND configures trigger when all conditions are fulfilled, OR configures trigger when even
one condition is fulfilled.
Chap.8 Trigger Condition
8-10
8.3 Connecting Device Communication
You can not operate anything with trigger only. Then, if you connect the established trigger to device communication, device
communication is available.
[Procedures]
(1) [After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) After selecting the row to be connected to device communication, select the first one of the rows to be connected
device communication.
(3) Press the button of the below arrow direction or double-click the cell to open device communication list.
(4) Select the one of device communication list and double-click it.
(5) Then, selected device communication is connected.
Notice
(1) The maximum number of connected device communication is 255.
(2) When trigger is configured, connected device communication works as procedures.
(3) In the case of the given example, when the value of bit device HX00000 is on, one bit data from the device HX500 is
written to bit device HX600 and HX400 of XP2
8.4 Deleting Connected Device Communication
[Procedures]
(1) [After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) Select the device to be deleted.
Chap.8 Trigger Condition
8-11
(3) Select [Edit]-[Delete] menu.
Notice
(1) The function to delete two devices at once is not available.
Chap.8 Trigger Condition
8-12
8.5 Editing Connected Device Communication
[Procedures]
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) Select the device to be edited.
(3) Double-click it or press Enter button.
(4) Edit the details of device communication.
(5) Press OK button to save changed details.
Chap.8 Trigger Condition
8-13
8.6 Deleting Trigger Condition
[Procedures]
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) Select the trigger list to be deleted.
(3) Select [Edit]-[Delete] menu.
(4) Then, selected item is deleted.
Chap.8 Trigger Condition
8-14
8.7 Trigger Copy/Paste
[Procedures]
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties]
(2) Select the trigger to be copied.
(3) Select [Edit]-[Copy] menu.
(4) Select the row for Paste.
(5) Select [Edit]-[Paste] menu.
(6) Then, the trigger is pasted.
Notice
(1) If the row for Paste is already declared trigger, overwrite is available.
(2) You can not copy the connected device communication only.
(3) You can perform Copy/Paste to other XP-Manager.
(4) When the device of copied trigger is pasted, it may not be displayed. If the PLC Driver of copied node is different
form the PLC Driver of pasted node, it is not displayed.
3.1
Chap.8 Trigger Condition
8-15
8.8 Trigger Cut/Paste
[Procedures]
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties].
(2) Select the trigger to be copied.
(3) Select [Edit]-[Cut] menu.
(4) Then, selected row is deleted.
(
5)Select the row for Paste.
(6)Select [Edit]-[Paste] menu.
(7) Then, the trigger is pasted.
8.9 Trigger Condition Drag & Drop
[Procedures]
Chap.8 Trigger Condition
8-16
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties].
(2) Select the edge of row to be dragged and click the left mouse button.
(3) Put the mouse to the position to be dragged and out it away.
(4) You can see that the selected row is moved.
Notice
(1) The Drag & Drop function at the identical screen is the same as Copy/Paste.
(2) The Drag & Drop function to other screen is the same as Copy/Paste.
(3) If you drop with pressing Ctrl button, Copy/Paste function at the same screen.
Chap.8 Trigger Condition
8-17
8.10 Undo Edition for Trigger Condition
[Procedures]
(1) After selecting [Trigger Condition] from a project screen, select or double-click [View]-[Properties].
(2) Select the row to be deleted.
(3) Select [Edit]-[Delete] menu and delete it.
(4) Select [Edit]-[Undo] menu.
(5) It returns to the previous status before edition.
Notice
(1) You need the previous edition history to Undo Edition.
(2) Redo Edition is not limited in the quantity.
(3) You can Undo Edition for all functions.
8.11 Redo Trigger Condition
[Procedures]
Chap.8 Trigger Condition
8-18
(1) After selecting [Device Communication] from a project screen, select or double-click [View]-[Properties].
(2) Select the row to be deleted.
(3) Select [Edition]-[Delete] menu and delete it.
(4) Select [Edit]-[Undo] menu.
(5) Then, it returns to the previous status before edition.
(6) Select [Edit]-[Redo] menu.
(7) Then, selected row is deleted again.
Notice
(1) Redo Edition is not limited in the quantity.
(2) You need the previous edition history to Redo Edition.
Chap.8 Trigger Condition
8-19
8.12 Trigger Condition Print Preview
[Procedures]
(1) After selecting [Trigger Condition] at a project screen, select or double-click [View]-[Properties].
(2) Select Trigger Condition screen.
(3) Select [Project]-[Print Preview] menu.
[Screen]
[Description on a screen]
Item Description
Print(a) It prints the current screen.
Next(b) It previews the next screen.
Previous (c) It previews the previous screen.
Two Pages(d) It previews two pages per screen.
Zoom In (e) It expands the current screen to full size.
Zoom Out(f) It reduces the current Preview Screen.
Close(g) It closes the Preview Screen and moves to the Edition Screen.
Screen(h) It previews the current screen.
Notice
(1) It is printed as Preview Screen.
(2) Through Preview Screen, you can adjust the screen not to be cut with the width of row.
(3) Edition is not available at Preview Screen.
(a) (b) (c) (d) (e) (f) (g)
(h)
Chap.8 Trigger Condition
8-20
8.13 Printing Trigger Condition
[Procedures]
(1) After selecting [Trigger Condition] at a project screen, select or double-click [View]-[Properties].
(2) Select Trigger Condition screen.
(3) Select [Project]-[Print] menu.
(4) The Print Dialog Box will be shown as below.
(5) Then, press [OK] button to print it.
Notice
(1) The below Pint Dialog Box may be different from Windows version.

Chap.9 View
9-1
Chap.9 View
9.1 Tools
You can show or hide docking screen.
[[Procedures]
(1) Select [View]-[Tools] menu.
(2) Select the name of a screen.
(3) The selected screen will be shown or hidden.
Notice
(1) You can show or hide project screen, online screen, output screen, monitor screen.
Chap.9 View
9-2
9.2 Full Screen
[Procedures]
(1) Open device communication screen or trigger condition screen.
(2) Select [View]-[Full Screen] menu.
(3) All tool bars and docking screens will disappear and the current screen will be a full size.
(4) If you press Close Full Screen or ESC button, it will back to the initial screen.
Chap.9 View
9-3
9.3 New Screen
[Procedures]
(1) Open device communication screen or trigger condition screen.
(2) Select [Window]-[New Window] menu.
(3) The screen that is the same as current selected screen is opened.
Notice
(1) The new screen is opened as the type of [Screen name: number].
(2) If edition proceeds at opened new screen, the same screens will be renewed all.
Chap.9 View
9-4
9.4 Close All
You can close the opened screens at once.
[Procedures]
(1) Open device communication screen or trigger condition screen.
(2) Select [Window]-[Close All] menu.
(3) Then, all opened screens are closed.
Chap.9 View
9-5
9.5 Other Screen
You can check the list of opened screen and close or open it.
[Procedures]
(1) Open device communication screen or trigger condition screen.
(2) Select [Window]-[Windows] menu.
[Dialog Box]
[Description on a dialog box]
Item Description
Screen List (a) It displays the list of open screen at XP-Manager
Activate(b) It activates the screen selected from the list and closes a dialog box.
Close(c) It closes the screen selected from the list.
OK(d) It closes a dialog box.
(a)
(b)
(c)
(d)

Chap.10 Tool
10-1
Chap.10 Tool
10.1 Checking Error
It checks the project.
[Procedures]
(1) Open the project.
(2) Select [Tool]-[Check Program] menu.
(3) Check the error of a project.
(4) It displays the result at output screen.
[Screen]
[Description on a screen]
Item Description
Goto(a) It moves to the selected screen where error or alarm occurs from the list.
Show Error (b) It shows or hides error items at the list.
ShowWarning (c) It shows or hides alarm items at the list.
Show normal string (d) It shows or hides normal string item at the list.
Notice
(1) XP Link parameter is downloaded, error is checked. After checking, if there is error, download is not available.
(2) After checking, error is displayed as red characters.
(a) (b) (c) (d)
Chap.10 Tool
10-2
10.2 XP-Builder Execution
[Procedures]
(1) Select [Tool]-[Start XP-Builder] menu.
(2) If XP-Builder is installed, XP-Builder will be executed.
Notice
(1) For execution, XP-Builder version of more than 1.20should be installed.
(2) Select the node name from a project screen. If the property of selected node is [Auto creation from XP-Builder file
of computer], open connected XPD file.
Chap.10 Tool
10-3
10.3 Executing XP-VNC
[Procedures]
(1) Select [Tool]-[Start XP-VNC] menu.
(2) XP-VNC starts.
Notice
(1) For the details on XP-VNC, refer to the Chap.12 VNC Client and ActiveX.
(2) If you select the node from a project screen and apply [Connect to XGT Panel VNC Server] of context menu, it will be
automatically connected with executing XP-VNC. In this case, XP-VNC should be downloaded and XP-VNC
server should be under operation.
Chap.10 Tool
10-4
(3) If you select XGT Panel at online screen and apply [Connect to XGT Panel VNC Server] of context menu, it will be
automatically connected with executing XP-VNC.
Chap.10 Tool
10-5
10.4 Executing XP-Remote
[Procedures]
(1) Select [Tool]-[Start XP-VNC] menu.
(2) XP-VNC starts.
Notice
(1) If more than one XP-Remote is installed, the latest version of XP-Remote will run..
Chap.10 Tool
10-6
10.5 Customize
You can add the hotkey of menus and tool bar button.
10.5.1 Command
[Procedures]
(1) Select [Tool]-[Customize] menu.
(2) Select [Commands] tab.
(3) Select the menu where shortcut button will be added from the menu list with a tool bar.
Chap.10 Tool
10-7
(4) Drag & Drop the selected menu above the tool bar.
(5) Then, a new menu button will be added.
Notice
(1) The information on added button is saved at registry.
Chap.10 Tool
10-8
10.5.2 Tool Bar
You can add or delete a new tool bar.
[Procedures]
(1) Select [Tool]-[Customize] menu.
(2) Select [Tool Bars] tab.
[Dialog Box]
[Description on a dialog box]
Item Description
List(a) It shows tool bar list. It can show or hide tool bar by checking.
Reset (b) It restores the details of selected tool bar to the initial installed status.
ResetAll(c) It restores the details of all tool bars to the initial installed status.
New(d) You can make a new tool bar.
Rename (e) You can change the name of new tool bar but this option is not available for
the existing tool bar at initial installation.
Delete (f) You can delete new tool bar but this option is not available for the existing tool bar
at initial installation.
(a)
(b)
(c)
(d)
(e)
(f)
Chap.10 Tool
10-9
10.5.3 Keyboard
You can designate hotkey of menus.
[Procedures]
(1) Select [Tool]-[Customize] menu.
(2) Select [Keyboard] tab.
(3) Select the Command.
(4) Set new hotkeys.
(5) Press Allocation button.
[Dialog Box]
Item Description
Commands (a) Menu Command List
Assign (b) It allocates new hotkey settings to the command.
Remove (c) It deletes the designated hotkey.
Reset All (d) It renews hotkey for all commands.
Press New Shortcut key (e) It inputs a new hotkey.
(a) (b)
(c)
(d)
(e)
Chap.10 Tool
10-10
10.5.4 Menu
You can designate the hotkey of menus.
[Procedures]
(1) Select [Tool]-[Customize] menu.
(2) Select [Menu] tab.
[Dialog Box]
Item Description
Show Menu for (a) It selects menu.
Reset(b) It renews menu.
Select Context Menu (c) It selects context menu.
Reset (d) It renews context menu.
10.5.5 Option
[Procedures]
(1) Select [Tool]-[Customize] menu.
(2) Select [Option] tab.
(a) (c)
(b) (d)
Chap.10 Tool
10-11
[Dialog Box]
[Description on a dialog box]
Item Description
Show Screen Tips on toolbars (a)
When putting a mouse above tool bar, the menu name will displayed.
Show Shortcut keys in Screen
Tips (b)
In case that hotkey is designated for the menu, it is also displayed.
(a)
(b)
Chap.10 Tool
10-12
10.6 Option
You can change the options of XP-Manager.
10.6.1 Common Option
[Procedures]
(1) Select [Tool]-[Option] menu.
(2) Select [General] tab.
(3) Change the details and press OK button or Apply button.
[Dialog Box]
[Description on a dialog box]
Item Description
1:1 Connection when connecting
XGT Panel (a)
When XGT Panel is connected to Ethernet with a cross cable, the option can be
applied.
Close transmission dialog box
automatically when transmission
is successfully completed (b)
The option closes automatically the dialog box when transmission dialog
box is successfully completed. In case that transmission dialog box fails,
dialog box is not closed automatically.
(a)
(e)
(b)
(c)
(d)
Chap.10 Tool
10-13
Item Description
Refresh interval of online window
(c)
You can change the searching cycle of XGT Panel at online screen.
Refresh interval of monitor (d)
You can change the cycle to import the data from XGT Panel during monitoring.
Chap.10 Tool
10-14
Item Description
Time Out of Monitor (e) If you fail to import the data from XGT Panel, you can designate time out.
10.6.2 Project Options
[Procedures]
(1) Select [Tool]-[Option] menu.
(2) Select [Project] tab.
(3) Change the details and press OK button or Apply button.
[Dialog Box]
[Description on a dialog box]
Item Description
Default Project storage Path
(a)
When saving the project first since its creation, you can designate the path.
Create Backup File (b) When opening the previous saved project and save it, you can back up the
previous file. The extension of backup file is between bk0 and bk9.
The number of Backup files
(c)
You can designate the number of backup files up to 9EA. bk0 is the latest backup file.
Use AutoSave (d) It can be automatically saved during using XP-Manager.
Interval of AutoSave (e) You can set automatic save interval between 3 minutes and 60 minutes.
Display message in case file
name is different with project
name when saving (f)
In case the file name is different from the project name, the below message may be shown
during save. If Yes is selected, the project name will be changed into the file name equally.
(a)
(e)
(b)
(c)
(d)
(f)
(g)
(h)
(i)
Chap.10 Tool
10-15
Item Description
No. of recent projects to
display(g)
For the latest row, you can change the maximum number of displayed projects.
Display dialog box to select
project when starting (h)
You can set whether project selection dialog box will be shown or not when starting
XP-Manager.
Display node IP address in
window title (i)
You can select whether the IP address of node will be displayed at the screen name or
monitor tab name.

Chap.11 Communication
10-1
Chap.11 Communication
11.1 XP Link Parameter Download
You have to download XP Link parameter to operate device communication between XGT Panels.
[Procedures]
(1) Open the project.
(2) Select [Communication]-[Download XP Link Parameter] menu.
(3) Check the node for download and press OK button.
(4) Perform error inspection for the checked node.
Chap.11 Communication
10-2
(5) If it has been proved that there is no error, proceed to download.
Notice
(1) As the result of inspection, the error is displayed as red character
Chap.11 Communication
10-3
11.2 XP Link Parameter Upload
You can read uploaded project made by XP-Manager from XGT Panel and open the project.
[Procedures]
(1) Select [Communication]-[Upload XP Link Parameter] menu.
(2) Check the XGT Panel to be uploaded and press OK button.
Chap.11 Communication
10-4
(3) Then, the opened project is closed and upload will be performed.
(4) Uploaded project will be open.
Notice
(1) If there is something to be revised at the current project, check whether it will be saved or not.
Chap.11 Communication
10-5
11.3 XP-VNC Server Management
You can download XP-VNC server to XGT Panel and set download XP-VNC parameter. For more details on XP-VNC, refer to
the [Chap.12 VNC Client and ActiveX].
[Procedures]
(1) Select the node from a project screen or select the XGT Panel searched from online screen.
OR
(2) Select [Communication]-[XP-VNC Server Management] menu.
11.3.1 XP-VNC Server Download
[Procedures]
(1) Select [Flash Memory (XGT Panel)] at the

item.
(2) Press Set (c) button.
(3) Then, XP-VNC server is downloaded.
[Dialog Box]
► XGT Panel does not basically provide VNC function. To use VNC function, you need to download
parameter and server.
Caution
Chap.11 Communication
10-6
[Description on a dialog box]
Item Description
Location at XGT Panel (a) The position of XP-VNC server file that is already installed at connected
XGT Panel
Download to (b) You can set the position of XGT Panel to be downloaded newly.
Set (c) You can download or delete XP-VNC server.
Auto run when starting XGT Panel (d) XP-VNC server is automatically executed when starting XGT Panel.
Set (e) It downloads XP-VNC server parameter.
Start XP-VNC Server (f) It starts to operate XP-VNC Server of target XGT Panel.
Stop XP-VNC Server (g) It stops to operate XP-VNC server of target XGT Panel.
Link XP-VNC Server (h) It executes XP-VNC client and connects XP-VNC of the target XGT Panel.
Copy XP-VNC ActiveX for web
server to clipboard (i)
It copies ActiveX for XP-VNC and HTML file with usage example to
a clipboard. After executing Windows Explorer, you can paste and use them.
Notice
(1) You cannot operate XP-VNC only with downloading XP-VNC server. Press XP-VNC Server Start(f) button to start
XP-VNC server.
(a)
(e)
(b)
(c)
(d)
(f)
(g)
(h)
(i)
Chap.11 Communication
10-7
11.3.2 Deleting XP-VNC Server
[Procedures]
(1) Select [Remove] at the

item.
(2) Press [Set(c)] button.
Notice
(1) If you press Refresh button and [Location at XGT Panel(a)] is displayed as “Not Installed”, you can check whether
XP-VNC Server is deleted properly.
Chap.11 Communication
10-8
11.4 Web Server Management
You can download web server to XGT Panel and set download parameters.
[Procedures]
(1) Select the node from a project screen or select the XGT Panel searched from online screen.
OR
(2) Select [Communication]-[Manage Web Server] menu.
► XGT Panel does not basically provide web server function. To use web server, you need to
download parameter and web server.
Caution
Chap.11 Communication
10-9
11.4.1 Web Server Download
[Procedures]
(1) Select [Flash Memory (XGT Panel)] at [Download to (b)] item.
(2) Press [Sett (c)] button.
(3) Then, web server is downloaded.
[Dialog Box]
[Description on a dialog box]
Item Description
Location at XGT Panel (a) The position of web server file that is already installed at connected XGT Panel
Download to (b) You can set the position of XGT Panel to be downloaded newly.
Setting (c) You can download or delete web server.
HTML file location (d) It sets the position of HTML file used for web server.
Server Port (e) It inputs Ethernet Port No. that is opened at web server all the time.
Home page (f) It inputs the name of the page to be shown first when web server is started.
Auto run when starting XGT Panel (g) Web server is automatically executed when starting XGT Panel.
Setting(h) It downloads web server parameter.
Start web server operation (i) It starts to operate web server of target XGT Panel.
Stop web server operation (j) It stops to operate web server of target XGT Panel.
(a)
(e)
(b)
(c)
(d)
(f)
(g) (h)
( I ) (j)
(k)
Chap.11 Communication
10-10
Link Web Server (k) It executes internet and connects web server of the target XGT Panel.
Notice
(1) You cannot operate web server only with downloading web server. Press Start (i) to start web server.
(2) The Web Server Port No. “80” is international standard port numberto change the port number., you need to input and
connect the port number when connecting web server. (Server IP Address: Port No.)
11.4.2 Deleting Web Server
[Procedures]
(1) Select [Remove] at [Download to (b)] item.
(2) Press [Set(c)] button.
Notice
(1) If you press Refresh button and the [Location at XGT Panel] is displayed as “Not Installed”, you can check whether
XP-VNC Server is deleted properly.
Chap.11 Communication
10-11
11.5 RAPIEnet Driver Management
You can download and delete the device driver for RAPIEnet Aux Card.
[Procedures]
(1) Select the node from a project screen or select the XGT Panel searched from online screen.
OR
(2) Select [Communication]-[Manage Driver] menu.
Select [RAPIEnet] tab.
[Dialog Box]
Chap.11 Communication
10-12
[Description on a dialog box]
Item Description
Location at XGT Panel (a) The position of RAPIEnet server file that is already installed at connected
XGT Panel
Download to (b) It sets the position of XGT Panel to be downloaded newly.
Setting (c) You can download or delete RAPIEnet Driver.
Notice
(1) You can set RAPIEnet parameter and communication through XP-PD.
(a)
(b)
(c)
Chap.11 Communication
10-13
11.6 Program Monitor Driver Management
You can download or delete the program monitor driver of LS ELECTRIC PLC CPU Driver.
[Procedures]
(1) Select the node from a project screen or select the XGT Panel searched from online screen.
OR
(2) Select [Communication]-[Manage Driver] menu.
(3) Select [Program Monitor] tab.
[Dialog Box]
Chap.11 Communication
10-14
[Description on a dialog box]
Item Description
Location at XGT Panel (a) The position of Program Monitor Driver file that is already installed at
connected XGT Panel
Download to (b) It sets the position of XGT Panel to be downloaded newly.
Language (c) It selects the language displayed at program monitor.
Font (d) It sets the font used for program monitor. When the established font
file is downloaded, the file size should be considered.
Setting (e) You can download or delete Program Monitor Driver.
Notice
(1)When monitoring Ladder Program, you need to select “ANSI Latin 1 1252” to display the program in English.
If “ANSI/OEM Korean Unified Hangul 949” is selected, the program is displayed in Korean
(a)
(b)
(e)
(c)
(d)
Chap.11 Communication
10-15
11.7 NC Program Monitor Driver Management
You can download or delete the program monitor driver of LS ELECTRIC PLC CPU Driver
[Procedures]
(1) Select the node from a project screen or select the XGT Panel searched from online screen.
OR
(2) Select [Communication]-[Manage Driver] menu.
(3) Select [Program Monitor] tab.
[Dialog Box]
(a)
(b)
(c)
(d)
(e)
Chap.11 Communication
10-16
[Description on a dialog box]
Item Description
Location at XGT Panel (a) The position of Program Monitor Driver file that is already installed at
connected XGT Panel
Download to (b) It sets the position of XGT Panel to be downloaded newly.
Language (c) It selects the language displayed at program monitor.
Font (d)
It sets the font used for program monitor. When the established font
file is downloaded, the file size should be considered.
Setting (e) You can download or delete Program Monitor Driver.
Notice
(1) "ANSI/OEM Korean Unified Hangul 949" shall be used to indicate the Korean language used in the program when
monitoring the ladder program.
You must make a selection When "ANSI Latin 1 1252" is selected, only English is displayed.
(2) When downloading a font file, be aware of the font file size.
Chap.11 Communication
10-17
11.8 FTP Server
You can set whether to use an FTP server driven by HMI and the folder on the XGT Panel to provide FTP services.
[Procedures]
(1) Select the node from a project screen or select the XGT Panel searched from online screen.
OR
(2) Select [Communication]-[Manage Driver] menu.
(3) Select [Program Monitor] tab.
[Dialog Box]
[Description on a dialog box]
(a)
(b)
(c)
(d)
Chap.11 Communication
10-18
Item Description
Whether to set the server path (a) Use : Use the FTP server service on the XGT Panel.
Not use: XGT Panel 에서 FTP 서버 서비스를 사용하지 않습니다.
Root Directory(b) The FTP server service is disabled on the XGT Panel.
Directory(c)
If you are using an FTP server, specify an accessible path.
For example, the iXP2 series is as follows.
 If you want to access the LSISProduct folder in the FlashDisk folder
on the XGT Panel, you can set the top-level folder to "Flash memory
(XGT Panel)" and set it to "LSISProduct" in the directory. If you want
to access a subfolder of LSISProdcut, you can use
LSISProcessDrivers.
UserSetting(d) Set up an account that can connect to the FTP server
Anonymous(e) Enable all users to connect.
ID/Password(f) Set account information
Setting(g) Lets you apply the above set items to the XGT Panel, such as whether to set
the server path.
Noties
(1) Only available in the iXP2 Series. (Excluding iXP2H-0702D and iXP2H-0704D.)
(2) To access FTP through command, enter ftp ip address in the cmd window.
The user is Anonymous, and the password can be entered as [password] if you do not have an email.
(3) To access the directory you set up after setting it up as above, you can install a free-for-deployment FTP Client to access
the folder as shown below.
(Ex. https://winscp.net/eng/docs/free_ftp_client_for_windows)
You can use anonymous authentication or anonymous.
Chap.11 Communication
10-19
Chap.11 Communication
10-20
11.9 Managing Autoscan Drivers
You can download and remove Autoscan drivers to view the configuration and module status of network systems configured
with RAPIENet I/F modules in PLC associated with HMI devices, and to measure cable distances.
[Procedures]
(1) Select a node in the Project window, or select the XGT Panel found in the Online window.
OR
(2) Select Menu [Communication]- [Driver/Service Management].
(3) Select the Autoscan tab.
Chap.11 Communication
10-21
[Dialog Box]
[Description on a dialog box]
Item Description
Location on XGT Panel (a) Displays the location of the Autoscan file that is already installed on the associated XGT
Panel.
Where to Download (b) Specify the location of the new XGT Panel to download.
Language settings (c) Under Autoscan, select the language that appears.
Download font file (d) Uncheck if you do not want to download the font file to the XGT Panel. Autoscan appears
in English only.
Font (e) Specifies the font that Autoscan will use. The specified font file will be downloaded and
you will need to consider the file size.
(a)
(b)
(f)
(c)
(d)
(e)
Chap.11 Communication
10-22
Setting (f) You can download or remove the Autoscan driver..
Notice
(1) "ANSI/OEM Korean Unified Hanul 949" must be selected to display the Hangul used in the program when monitoring
Autoscan. If you select "ANSI Latin 1 1252", only English is displayed.
(2) When downloading font files, be aware of font file size.
(3) Only iXP2 series have the appropriate driver function..
Chap.11 Communication
10-23
11.10 XGT Panel Update
You can continuously update XGT Panel of network.
[Procedures]
(1) Select [Communication]-[Update XGT Panel] menu.
(2) Set the position of update file (b).
(3) Check XGT Panel (a) to be updated.
(4) Press OK button to update XGT Panel.
[Dialog Box]
[Description on a dialog box]
Item Description
XGT Panel List(a) It is the XGT Panel list displayed at online screen. The checked item
will be updated.
File Path (b) It is the folder where XP-Runtime of XGT Panel is placed.
Notice
(1) XP-Runtime is the software for monitor operated at XGT Panel.
(a)
(b)
Chap.11 Communication
10-24
11.11 XGT Panel Information
You can check the information of XGT Panel with various settings.
11.11.1 General
[Procedures]
(1) Select the node from a project screen or select the XGT Panel searched from online screen.
OR
(2) Select [Communication]-[XGT Panel information] menu.
(3) Select [General] tab.
(4) Check the information of XGT Panel.
[Dialog Box]
(a)
(b)
Chap.11 Communication
10-25
[Description on a dialog box]
Item Description
Information(a)
XGT Panel It displays the type of XGT Panel.
OS Version It displays the OS version of WinCE embedded with XGT Panel
State It displays the current operation status of XGT Panel.
Version It displays the version of XP-Runtime.
File Version It displays the version of drawing file downloaded from XP-Builder
Flash Memory It displays Flash Memory Occupation.
CF Card In case that CF Memory is embedded, it displays CF Memory occupation.
USB Memory In case that USB Memory is embedded, it displays USB Memory occupation.
PLC0 ~ PLC3 It displays the PLC Driver name used for drawing. It is displayed up to 4EA.
Refresh (b) It updates the details.
11.11.2 Setting
[Procedures]
(1) Select the node from a project screen or select the XGT Panel from online screen.
OR
(2) Select [Communication]-[XGT Panel Information] menu.
(3) Select [Settings] tab.
(4) The details are changed.
Chap.11 Communication
10-26
[Dialog Box]
[Description on a dialog box]
Item Description
Touch buzzer sound (a) It sets whether buzzer or beep sounds when manipulating the touch screen of XGT Panel.
Set (b) It applies the property of buzzer sound effect when touching the screen to XGT Panel.
Arabic Font supported
(c)
It provides the display mode for Arab language font written from the right to the left.
Set (d) It applies the property of Arab language font to XGT Panel.
Keep-Alive time (e) If TCP/IP Slave PLC Driver is embedded, it sets the time for a client to check the connection
status.
Set (f) It applies the property of time to keep connection to XGT Panel.
Alias name (g) It gives XGT Panel a byname.
Set (h) It applies the property of machine name to XGT Panel.
Notice
(1) English/Korean/ Chinese are available for XGT Panel menu language.
(a) (b)
(c) (d)
(e) (f)
(g) (h)
Chap.11 Communication
10-27
11.11.3 Clock
[Procedures]
(1) Select the node from a project screen or select the XGT Panel searched from online screen.
OR
(2) Select [Communication]-[XGT Panel Information] menu.
(3) Select [Clock] tab.
(4) Change a clock
[Dialog Box]
(a) (d)
(b)
(c)
Chap.11 Communication
10-28
[Description on a dialog box]
Item Description
Date (a) It changes the date.
Time (b) It changes the time.
Synchronize with PC time (c) It changes the clock of XGT Panel with the date and time of a computer.
Setting (d) It changes the clock of XGT Panel with input date (a) and time (b).
11.11.4 Password
[Procedures]
(1) Select the node from a project screen or select the XGT Panel searched from online screen.
OR
(2) Select [Communication]-[XGT Panel Information] menu.
(3) Select [Password] tab.
(4) Set or delete password.
Chap.11 Communication
10-29
[Dialog Box]
[Description on a dialog box]
Item Description
Previous Password (a) If you try to delete or change password, you are required to input the previous one.
New Password(b) Input a new password.
Confirm Password(c) Input the same password as that of New Password (b).
Delete (d) It deletes the existing password set by XGT Panel.
Set (e) It sets a new password.
Notice
(1) A Password is case-sensitive.
(2) Special characters can be applied to a password.
(3) The maximum digit of a password is 10.
(a) (d)
(b)
(c)
(e)

Chap. 12 Monitor
12-1
Chap. 12 Monitor
12. 1 Monitor Registration
You can monitor the device data of XGT Panel and change the value.
12.1.1 Registration by editing directly
[Procedures]
(1) Open the project.
(2) Select the monitor screen.
(3) Select the node screen (g) to register monitor.
(4) Establish the type.
(5) Input the device name and register a monitor.
[Screen]
[Description on a screen]
Item Description
Type (a) It selects the type of device to be monitored.
Start Monitor (b) It starts or terminates to monitor the devices to be registered.
Name(c) It inputs the name of the device to be monitored.
Hexadecimal display (d) It can display the value as hexadecimal.
Value (e) It displays the device value read from XGT Panel.
Description(f) It can input the comment for the device to be monitored.
Node Screen (g) One monitor screen is allocated for each node of project and you can select node screen.
(a) (b) (c) (d) (e) (f)
(g)
Chap. 12 Monitor
12-2
Notice
(1) You can register the monitor without limitation in the number.
(2) You can register the monitor with tag.
(3) If you input the name of proper device first without inputting the type, you can register a monitor.
(4) The device whose monitor is registered is saved at project file(XPD file)
(5) When the node is added to project, the monitor screen is added to node screen (g).
(6) If the node is deleted from the project, the monitor screen will be deleted from the node screen (g).
12.1.2 Registration by Drag & Drop from tag screen
[Procedures]
(1) Open the project.
(2) Double-click the tag at project screen and open tag screen.
(3) Select the edge of the tag for monitor registration and drag it to monitor screen.
Chap. 12 Monitor
12-3
(4) Drop it to monitor screen.
(5) Then, it is registered to the monitor.
Notice
(1) You can select and register several tags.
(2) If tag is moved to the different node screen, it may not be registered properly.
(3) If the description (f) is changed, the description on tag is not changed. Namely, the description of monitor device is quite
different from the tag description.
(4) If the name or type of tag is changed, error may occur from the tag registered at monitor screen.
Chap. 12 Monitor
12-4
12.1.3 Registration by Drag & Drop from device communication screen
[Procedures]
(1) Open the project.
(2) Double-click device communication from a project screen and open the tag screen.
(3) Select the edge of device communication edge for monitor registration and drag it to the monitor screen.
(4) Drop it to the monitor screen.
Chap. 12 Monitor
12-5
(5) It is registered to the monitor.
Notice
(1) You can select and register several device communications.
(2) If the tag is applied under device communication, it is registered as tag.
(3) All devices used under device communication are registered.
12.1.4 Registration by Drag & Drop from trigger condition
[Procedures]
(1) Open the project.
(2) Double-click the device communication from a project screen and open the tag screen.
Chap. 12 Monitor
12-6
(3) Select the edge of trigger condition for monitor registration and drag it to the monitor screen.
(4) Drop it to the monitor screen.
(5) It is registered to the monitor.
Notice
(1) You can select and register several trigger conditions.
(2) If tag is applied under trigger condition, it is registered as tag.
(3) All devices used in Trigger are registered but devices used in Linked device communication are not registered.
Chap. 12 Monitor
12-7
12.2 Deleting Monitor
[Procedures]
(1) Open the project.
(2) Select the monitor screen.
(3) Select the node screen (g) for monitor registration.
(4) Select the monitor time to be deleted.
(5) Select [Edit]-[Delete] menu.
(6) Then, selected item will be deleted.
Chap. 12 Monitor
12-8
Notice
(1) To delete the input details, double-click the comment and press Back space key at edition mode.
Chap. 12 Monitor
12-9
12.3 Monitor Copy/Paste
[Procedures]
(1) Open the project.
(2) Select the monitor screen.
(3) Select the node screen (g) for monitor registration.
(4) Select the monitor time to be copied
(5) Select [Edit]-[Copy] menu.
(6) Move to the cell for Paste.
(7) Select [Edit]-[Paste] menu.
Notice
(1) You can select several monitor items and perform Copy/Paste.
Chap. 12 Monitor
12-10
12.4 Monitor Cut/ Paste
[Procedures]
(1) Open the project.
(2) Select the monitor screen.
(3) Select the node screen (g) for monitor registration.
(4) Select the monitor time to be cut.
(5) Select [Edit]-[Cut] menu.
(6) Move to the cell for Paste.
(7) Select [Edit]-[Paste] menu.
Notice
(1) Cut mode is same as Delete after Copy.
Chap. 12 Monitor
12-11
12.5 Starting Monitor
[Procedures]
(1) Open the project.
(2) Select the monitor screen.
(3) Select the node screen (g) for monitor registration.
(4) Register the monitor.
(5) Press Start Monitor button.
(6) Then, monitor is started.
(7) Press Stop Monitor button.
Notice
(1) In case that the XGT Panel is not under monitoring, you can start monitor with the below error message.
(2) If monitor is started, the value will be displayed as blue letters.
(3) After starting monitor, if communication is not connected, “Timeout” will be shown as red letters.
Chap. 12 Monitor
12-12
12.6 Changing the current value
[Procedures]
(1) Open the project.
(2) Select the monitor screen.
(3) Select the node screen (g) for monitor registration.
(4) Register the monitor.
(5) Press Start Monitor button.
(6) Then, monitor is started.
(7) Select the monitor item to be changed.
(8) Select [Change value] of context menu.
(9) After inputting a new value at ‘Change value’ dialog box, press OK button to change the value of XGT Panel.
[Dialog Box]
[Description on a dialog box]
Item Description
Name(a) The name of the item to be changed or tag name is displayed.
Type(b) It is the type of the item to be changed.
Device(c) It is the name of device to be changed.
Value(d) Input the value to be changed.
(a)
(d)
(b)
(c)
Chap. 12 Monitor
12-13
Notice
(1) If wrong value is input or it exceeds the limited range, the below error message will be shown.
Chap. 12 Monitor
12-14
12.7 Monitor Stop
[Procedures]
(1) Open the project.
(2) Select the monitor screen.
(3) Select node screen (g) for monitor registration.
(4) Register the monitor.
(5) Press Start Monitor button.
(6) Then, monitor is started.
(7) Press Stop Monitor button.
(8) Monitor is stopped.

Chap.13 Monitoring XGT Panel screen at PC and web environment
13-1
Chap.13 Monitoring XGT Panel screen at PC and web environment
13.1 Monitoring XGT Panel screen at PC Environment

XP-VNC Client is the tool to check/control the operation data and status of XGT Panel through single application. Namely, the
controller such as PLC is not directly monitored, operated by XGT Panel but it is monitored by PC connected with XGT Panel.

One XP-VNC Client can be connected to several XGT Panels and it can monitor and operate each XGT Panel.
But, one XGT Panel can be connected to one XP-VNC client.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-2
13.2 Operating XP-VNC Client

The operation processes for XP-VNC Client are as below.
To monitor the XGT Panel screen at a PC; first, start XP-VNC Client of XP Manager. Second, operate XP-VNC server
downloaded at XGT Panel to be connected. A user can set the options of XP-VNC Client (resolution, screen capture position,
etc.) depending on the circumstances. After the above processes are completed, connect VNC server of the related XGT Panel
at XP-VNC Client of PC. After monitoring XGT Panel screen is completed, terminate XP-VNC Client. For more details and
process, refer to the below.
13.2.1 Operating XP-VNC Server
To operate XP-VNC Client, you need to run XP-VNC server downloaded at XGT Panel. There are two methods to operate
XP-VNC Server as below.
1) Operate it through [XP-Manager]-[Communication]-[Manage XP-VNC Server]. For more details on XP-VNC, refer to [10.3
XP- VNC Server Management].

Operating XP-VNC Server
Starting XP-VNC Client
Connecting XP-VNC Client and XP-Server
Setting the option of XP-VNC Client
Ending XP-VNC Client
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-3
2) After selecting the node IP to be connected among the nodes connected XP-Manager, press the right mouse button and
select [Manage XP-VNC Server].
13.2.2 Starting XP-VNC Client
There are three methods to start XP-VNC Client as below.
1) Execute [Start]-[LSIS]-[XP-Manger 1.00]-[XP-VNC].
2) Execute XP-VNC at XP-Manager.
3) After selecting node added by XP-Manager, press the right mouse button and select [XP-VNC Server Connection].
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-4
Notice
You can directly monitor the target XGT Panel screen without starting XP-VNC Client.
Methods
1. After selecting the node of XGT Panel or IP address connected by XP-Manager, press the right mouse button.
2. Select [XGT Panel VNC Server Connection] with the right mouse button.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-5
If you execute XP-VNC through the above method, the Start Screen will be not displayed but XGT Panel screen
will be displayed directly.

13.2.3 Setting the option of XP-VNC Client
Before connecting XP-VNC Client and XP-VNC Server of XGT Panel, a user can set the options of XP-VNC
Client(resolution, screen capture position, etc). For more details on setting XP-VNC Client options, refer to [Connection
Option] of [12.4 XP-VNC Client Tool Box].
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-6
13.2.4 Connecting XP-VNC Client and XP-VNC Server
If you press [Connect] button at connection screen of XP-VNC Client started through the method from 12.2.2, the related
server will be connected. It is properly connected provided that XP-VNC server works.
If you press [Connect] button at connection screen of XP-VNC Client as above, it is connected to XGT Panel VNC-Server
and the target XGT Panel screen is displayed at PC. For more details on XP-VNC Client screen, refer to [12.3 XP-VNC
Client Screen Composition].
13.2.5 Ending XP-VNC Client
It terminates connection of XP-VNC Client. For details on terminating XP-VNC Client, refer to [Tool Box] of [12.4 XP-VNC
Client Tool Box].
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-7
13.3 XP-VNC Client Screen Composition
The execution screen of XP-VNC Client has the below composition.
Item Description
VNC Server(a)
Input the IP address of XGT Panel to be connected.
(VNC Server should be operated at the XGT Panel to be connected)
The Server IP list of XGT Panel recently connected is displayed at the combo box and you can
select the one from them.
Quick options (b)
Set communication speed with VNC Server of XGT Panel and color type to be displayed. In the
case of automatic setting, the color is automatically changed and displayed depending on
transmission speed.
View Only(c) Set whether the function to display screen only (Cannot input) is applied or not.
User’s input details is not transferred to XGT Panel but just XGT Panel screen is displayed
Auto Scaling (d)
In case that Automatic Size Adjustment is set, the size of VNC Client will be automatically set to
fit the size of PC monitor connected to XGT Panel. On the other hand, in case that Automatic
Size Adjustment is not set, XP-VNC Client is displayed as the size of XGT Panel.
Options (e) You can set the connection between XP-VNC Client and VNC Server. For more details, refer to
connection options of 12.4 Tool Box.
(a)
(b)
(d) (c)
(e) (f) (g)
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-8
Connect (f) Press the button to connect VNC server and VNC Client.
Cancel (g) You can cancel the execution of VNC Client.
The screen of connection between XP-VNC and XGT Panel is composed of below.
[Description on a dialog box]
Item Description
Title(a) It displays the IP of connected XGT Panel.
Tool Box(b) It offers the tools to execute the functions provided by XP-VNC.
Screen (c) It displays the screen of connected XGT Panel as it is.
(a)
(b)
(c)
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-9
13.4 The Composition of XP-VNC Client Tool Box
The frequently used functions of XP-VNC are provided as shortcut icons. [Tool Box] will be shown as below and refer to the
following each function.
[Tool Box]
(1) Full-Screen Transition
Item Description
Full-Screen Transition If Full-Screen Transition is not established, it is displayed as the size of
XGT Panel at the whole screen of PC monitor.
(2) Connecting Options
Item Description
Format and Encoding (a)
You can set the screen color to be displayed at XP-VNC.
In the case of Automatic Setting, the color is automatically changed depending on PC’s
communication speed as below.
Speed Color
1Mbit/s Full Colors
125 ~ 256 Kbit/s 256 Colors
128 ~ 19 Kbit/s 64 Colors
5 ~ 19 Kbit/s 8 Colors
Less than above Black & White
(1) (2) (3) (4) (5) (6) (7)
(a)
(h)
(b)
(c)
(d)
(e)
(f)
(g)
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-10
Item Description
Using 3 Button (b)
You can set whether a 3-button mouse will be used or not.
If the mouse connected to PC has three buttons, the option is set and you can
use light, middle, right buttons.
Swap 2
nd button and 3rd
button (c)
If you use 3-button mouse, set whether the operation of middle button and right
button will be exchanged or not.
Show Buttons Bar (d)
Set whether the tool box will be shown or not.
If you undo [Showing Tool Box], the tool box is not shown at XP-VNC Client.
View Only (Cannot Input)(e)
Set whether the function to transfer user’s operation to XGT Panel at XP-VNC Client
will be applied or not. If Displaying Screen Only is applied, any functions of XP-VNC
Client is not transferred to XGT Panel but just XGT Panel screen will be displayed.
If you undo Displaying Screen Only, the operations of XP-VNC Client are transferred
to XGT Panel. For example, if you press screen transition switch at XP-VNC Client,
it is moved to the screen.
Full Screen (f)
It is displayed at the full screen of a user’s PC. In the case, the size of a screen will be
equivalent to the size of XGT Panel.
(Refer to the figure of 12.3 The Composition of Screen).
Viewer scale (g)
You can adjust the size of a screen.(Refer to the figure of 12.3 The Composition of
Screen) For example, if the size of XGT Panel is 320 * 240 and the size of a screen
is 100%, the size of screen will be displayed as 320 *240.
Path of Screen Capture (h)
You can set the position to capture the current screen of XP-VNC Client
(Refer to the figure of 12.3 The Composition of Screen).
A user can set the upper position where the captured file will be saved
and Year/Month/Day folder is created at the established position with the image whose
file name is Hour/Minute/Second. bmp.
For the method to capture the screen, refer to (5) Screen Capture of 12.4
The Composition of Tool Box.
(3) Refresh
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-11
Item Description
Refresh
It newly displays the screen of XP-VNC Client.
If the data value is changed or the screen is converted, the event of XGT
Panel may not be transferred and displayed to XP-VNC Client in real time.
Namely, XP-VNC screen may not be updated immediately due to various
factors such as PC transmission speed and XGT Panel’s operation speed. In
this case, through Refresh mode, you can communicate with XGT Panel and
update XP-VNC screen with the XGT Panel screen.
(4) Connecting Information
Item Description
VNC Server It displays the IP address or name of the VNC Server that is connected
currently.
Port It displays the port No. connected to VNC Server.
Status
It displays the status of VNC Server.
For example, if it is connected to the server, [Under Connection] and if
password is set, [Checking password] will be displayed.
Encoder It indicates the status of screen encryption to transmit the screen. XP-VNC
Client and Server adopts only Raw type for encoder.
Speed
It indicates the communication speed between VNC Server and XP-VNC
Client. If encryption is automatically set at connection option, the color will be
changed depending on the above speed.
Traffic It indicates the communication amounts transmitted by sever and the
communication amount that XP-VNC Client receives.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-12
(5) Screen Capture
Item Description
Screen
Capture
It captures the screen of the current XP-VNC Client to designated position. (Refer to the figure of 12.3 The
Composition of Screen)
A user can set the upper position where the captured file will be saved and Year/Month/Day folder is created
at the established position with the image whose file name is Hour/Minute/Second. bmp.
For example, if the below screen is displayed and capture position is set as OS (C): /Program File (x86) /LS /
XP-Manager /20200513(Year/Month/Day) folder and 160326(Hour/Minute/Second).bmp file will be creased
as below.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-13
(6) Screen End
Item Description
Connection
End
It terminates execution of the current XP-VNC Client. Other method to terminate connection is press X
button that is on the upper right of XP-VNC Client.
(7) IP Input Screen
Item Description
IP Input Screen
When XP-VNC Client is in progress, if you try to connect other XGT Panel, input the IP address of
the server to be connected at IP Input Screen of the Client and press the left button of the screen.
Then, new XP-VNC Client will be created and display the related XGT Panel.
Namely, if you connect other XGT Panel through IP Input screen at executing XP-VNC Client, the
current XP-VNC Client will not be terminated but the existing connected XGT Panel will be
continuously displayed.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-14
Notice
(1) If the password is set for connected XGT Panel, when XP-VNC Client is executed, the password will be
requested with verification process. You can establish the password at [Communication]-[XGT Panel
Information]-[Password] of XP-Builder.
If XP-VNC Client is connected when the password is set for XGT Panel as above, password will be
requested with verification process as below. Although the allowable password for XP-Builder is 10 digits,
XP-VNC tries to connect to server when the password coincides with the 8th digits. If password verification
is failed, XP-VNC Client will be terminated.
(2) XP-VNC Client can be connected to one VNC Server. If VNC Server is connected to either one XP-VNC
Client or communication, other XP-VNC Client is the same VNC Server, the alarm message [Connection
to Server failed] will be shown.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-15
13.5 Monitoring XGT Panel Screen at web
XP-VNC ActiveX is the tool to check and control the data operated at XGT Panel and its status through web browser. Namely, it
does not directly monitor, operate the controller such as PLC at XGT Panel but monitors, operates the controller by connecting
XGT Panel at web browser of PC. XP-VNC ActiveX can connect to several XGT Panels with one PC like XP-VNC Client and
you can monitor, operate each XGT Panels.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-16
13.6 Starting
XP-VNC ActiveX is the application operated at web browser and you can download ActiveX from web browser. To download
ActiveX provided by XP-VNC, [Security] should be established at web browser as below. Select [Control panel]-[Internet
Options]-[Security]-[Custom Level] at web browser.
Enable the [Download unsignedActive X controls].
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-17
Enable [Initialize and script Active X controls not marked as safe.
Operation processes for XP-VNC ActiveX are as below. To execute XP-VNC ActiveX, both web server and VNC Server
should be operated at the same time.
To monitor the XGT Panel screen at web browser; first, operate the web server downloaded at the target XGT Panel. Second,
operate XP-VNC server downloaded at the XGT Panel as XP-VNC Client. The above two processes are the preconditions to
monitor XGT Panel screen at web browser.
Third, download XP-VNC ActiveX that is the application to display XGT Panel screen at web browser to the XGT Panel.
A user can set the options of XP-VNC Client (resolution, screen capture position, etc.) depending on the circumstances. After the
above processes are completed, connect VNC server of the related XGT Panel at web browser. After monitoring XGT Panel
screen is completed, terminate web browser. For more details and process, refer to the below.
Operating Web Server
Operating XP-VNC Server
Connecting XP-VNC ActiveX to XP-VNC Server
Setting XP-VNC ActiveX options
Ending XP-VNC ActiveX
XP-VNC ActiveX Download
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-18
13.6.1 Operating Web Server
To operate XP-VNC ActiveX, make sure to run web server. There are two methods to operate XP-VNC web server as
below.
1) Operate web server through [XP-Manager]-[Communication]-[Manage Web Server]. For more details on XP-VNC
Web Server, refer to [10.4 Web Server Management].
2) After selecting the node registered at XP-Manager, click the right mouse button and operate it through [Web Server
Management].
After executing as the above, make sure to press [Set] and [Start] as below.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-19
13.6.2 Operating XP-VNC Server
To operate XP-VNC ActiveX, for the details on XP-VNC Server, make sure to refer to [10.3 XP-VNC Server Management]
and [12.2.2 Operating XP-VNC Server] as XP-VNC Client.
13.6.3 Setting the options of XP-VNC ActiveX
A user can set the options (resolution, screen capture position, etc.) of XP-VNC ActiveX before connecting XP-VNC ActiveX
and XP-VNC of the target XGT Panel. For more details on setting the options of XP-VNC ActiveX, refer to [Connecting
Option] of [12.4 XP-VNC Client Tool Box Composition].
13.6.4 Downloading ActiveX Application and Connecting to Web Server, XP-VNC Server
For the method to connect XP-VNC ActiveX to server with downloading it, refer to the below. After selecting the node to
connected at XP-Manager, apply [Communication]-[Web Server Management] and press [Web Server Connection], web
browser will be executed automatically with the below screen.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-20
If you select [If you want to monitor XGT Panel, Click here] at the above web browser, it will be connected to the related XGT
Panel.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-21
Notice
(1) If you download ActiveX through [Communication]-[Manage Web Server], ActiveX cab file is automatically
downloaded to XGT Panel. Download route is the same as Flash memory where web server is located.
(2) If you try to execute web browser by downloading ActiveX .cab file and .html file to USB Memory or CF
Card, refer to the below. Select [Communication]-[Manage XP-VNC Server]-[Copy XP-VNC ActiveX for web
server to clipboard]. After that, paste it to USB Memory or CF Card and copy cab file and .html file.
Chap.13 Monitoring XGT Panel screen at PC and web environment
13-22
After copying the file to USB Memory or SD Card or CF Card with the above method, connect the Memory
Card to XGT Panel and input the IP to be connected at web browser, the below screen will be shown. Select
[If you want to see backup files, Click here] at the below screen and move to the route where the position is
located.
If you select XP-VncAx.htm from the above screen, the XGT Panel screen connected to memory card will be
displayed at web browser.

Usecase 1. Read and diplay value from XGTPanel.

HW00's Current Value: <% GetXPData("00000001 00FFFF81", "3", "4"); %>

Usecase 2. Write value to XGTPanel.

Usecase 3. Write value to XGTPanel with Setting dynamically.

device :

devSize :

devType :

value :

redirect :

Chap.16 Work Operation
16-1
Chapter 16 Work Operation
16.1 Various Works using Excel Template File
Please, refer to [Chapter 15 Excel Work].
Chap.16 Work Operation
16-2
16.2 XP-Server Recipe - CSV File
16.2.1 Various Works using Excel Template File
Action
● Write
Write the value corresponding to the recipe number among the values saved in [Write Source File] on the
target device.
☞Set [Write Source File](ServerRecipe.xls) as below.
Setting Item Setting Description
Write Source File
Name
CSVData.csv
Write Source File
Contents
Filename : C:CSVData.csv
☞Set Row Number
Set row number to display. Row number always starts from Row A.
Data area
Data area
Chap.16 Work Operation
16-3
☞Set a device
Set a target device as below.
Setting Item Setting Description
Target Node XP1(192.168.1.102)
Device Type 16bit unsigned
Count 5
Target Device P0000~ P0004
Once editing the content [Write Source File] as seen above is completed, the data corresponding to Row
No. 1 will be read from [Write Source File] and it will be used as the device value if the specified trigger
conditions are met.
Note
(1) Any Read-Only device cannot be set as a status device.
(2) In case of [Read] action, any Read-Only device cannot be set as a subject device.
(3) If any change in the TargetNode, TargetDevice or Device Type occurs, the device address will be initialized.
(4) Recipes are set in vertical.
(5) When specifying row number, any work will not activate if the specified number is not in the file.
Chap.16 Work Operation
16-4
16.3 XP-Server Logging - CSV File
Action
● Read
Write data of the specified device in a file.
☞Set file information as below.
Setting Item Setting Description
File Folder Logging
File Log_%Y_% _%D.csv
Save Append data to end of file
Time Attach time stamp in front of data
Chap.16 Work Operation
16-5
☞Set a device
Set a target device as below.
Setting Item Setting Description
Target Node XP1 (192.168.1.102)
Device Type 16bit unsigned
Count 4
Target Device P0000~P0004
Once editing the content of [Write Source File] as seen above is completed, four data starting from PLC
Device P0000 connected to XP2 will be saved if the specified trigger conditions are met.
Writing at the end of the file will be continued until the trigger conditions are met.
Time is displayed in front of four device data.
A result file will be created with the specified folder and name in the folder that has XP-Server’s execution
file.
Note
(1) Any Read-Only device cannot be set as a status device.
(2) In case of [Read] action, any Read-Only device cannot be set as a target device.
(3) If any change in the TargetNode, TargetDevice or Device Type occurs, the device address will be initialized.
(4) Recipes are set in vertical.
(5) If any non-existing number is specified in the file, no work will occur.
Chap.16 Work Operation
16-6
16.4 XP-Server’s Logging – Database
Action
● MS Access File
Save data of the specified device in MS Access File Database.
☞Database is set as below.
Setting Item Setting Description
Server Kind Microsoft Office Access
Driver Microsoft Office Access
File Name C:HMIDB mdb
☞Set a device
After clicking the device to be saved in the database, set a target device as below.
Chap.16 Work Operation
16-7
Setting Item Setting Description
Table Name Table Name
Field Field 1,Field 2,Field 3,Field 4
Node XP1,XP1,XP2,XP2
Type 16bit Signed,16bit Unsigned,32Bit Unsigned, 32Bit Signed
Device P0000,P0001,HW0000,HK0000
Once editing the content of DB as seen above is completed, the target node data corresponding to the field will be
read and recorded in MS AccessFile if the specified trigger conditions are met.
● SQL Server
Save data of the specified device in SQL Server Database.
DB and tables shall exist in SQL Server Database.
☞Database is set as below.

Setting Item Setting Description
Server Type SQL erver
Driver SQL Server
Server Name or IP Address ServerName
Database Name XPSServer
Login Name xp_user
Password xp_password
Connection Time Out 3 seconds
Chap.16 Work Operation
16-8
☞Set a device
After clicking the device to be saved in the database, set a target device as below.
Setting Item Setting Description
Table Name Table Name
Field Field 1,Field 2,Field 3,Field 4
Node XP1,XP1,XP2,XP2
Type 16bit Signed,16bit Unsigned,32Bit Unsigned, 32Bit Signed
Once editing the DB content as seen above is completed, the data of the target node data corresponding to the field
will be read and inserted to SQL Server in a manner that they are appropriate to the field and node mapping.
Note
(1) Any Read-Only device cannot be set as a status device.
(2) If there is no field, any data is not inserted.
(3) For DB Name, Login Name and Password, capital and small letters shall be distinguished when inputting.
Chap.16 Work Operation
16-9
16.5 Read/Write XGT Panel’s Recipe- CSV File
Action Setting Item Setting Content
Basic.
Recipe
As a recipe edited in XP-Builder, that is downloaded from XGT Panel’s project
file.
Recipe number refers to the number of the recipe edited in XP-Builder.
File Recipe It refers to a file recipe in XGT Panel’s USB or SD Card or CF Card.
Chap.16 Work Operation
16-10
It refers to file recipe number in XGT Panel’s USB or CF Card.
Recipe No. – Six digits at the end of a file recipe indicate its file number.
● Read
Write data of the specified device at a file.
☞Set file information as below.
Setting Item Setting Description
Action Read
File Read_Recipe.csv
Chap.16 Work Operation
16-11
☞Set information on the target recipe
Set information on the target recipe as below.
Setting Item Setting Description
Subject Node XP1(192.168.1.102)
Recipe Kind Basic.
Recipe No. 1
Once editing the content on file or subject recipe information as seen above is completed, data will be read
from XP1’s No. 1 Recipe and recorded in CSV File if the specified trigger conditions are met.
A result file will be created at the specified folder and as name in the folder that has XP-Server’s execution
file.
Chap.16 Work Operation
16-12
● Write
Write data of the specified device in a file.
☞Set file information as below.
Setting Item Setting Description
Action Write
File Write_Recipe.csv
☞Set information on the target recipe
Set information on the target recipe as below.
Chap.16 Work Operation
16-13
Setting Item Setting Description
Target Node XP1(192.168.1.102)
Recipe Type Basic.
Recipe No. 1
Once editing the content on file or target recipe information as seen above is completed, data will be read
from CSV File and recorded in XP1’s No. 1 Recipe if the specified trigger conditions are met.
Note
(1) Any Read-Only device cannot be set as a status device.
(2) When writing, no data will be recorded if there are less recipe blocks and rows or less devices and columns.
Chap.16 Work Operation
16-14
16.6 Read XGT Panel’s NVRAM Logging- CSV File
Action
● Read
Write data of the specified logging number in a file.
☞Set file information as below.
Setting Item Setting Description
Folder NVRAM_Logging
File Log_%Y_%M_%D
☞Set information on the target logging
Specify information on the target logging as below.
Chap.16 Work Operation
16-15
Setting Item Setting Description
Target Node XP1(192.168.1.101)
Logging No. Device Node XP2(192.168.1.102)
Device HW0000
Logging No.
Directly set the logging number to display.
For logging numbers, see XP-Builder’s illustration screen
If logging is selected from XP-Builder, logging number will appear in the logging setting window.
Set a logging number to display.
Once editing the content as seen above is completed, the logging number saved in XP2’s HW0000 will be
read and the logging data in XP1’s Node designated as a target node will be saved at a specified folder and
file if the specified trigger conditions are met.
A result file will be created at the specified folder and as name in the folder that has XP-Server’s execution file.
Logging Status
Logging Completed – Logging is successfully completed
Logging Abort – Logging is not successfully completed (Failed to communicate between PLC
and HMI)
Note
(1) Any Read-Only device cannot be set as a status device.
(2) Work ‘Read XGT Panel’s Logging’ creates CSV files every time CSV File.
Logging no.
No. Logging status Date Value
Chap.16 Work Operation
16-16
16.7 Read XGT Panel’s NVRAM Alarm – Unicode Text File
Action
● Read
Write data of the specified alarm number in a file.
☞Set file information as below.
Setting Item Setting Description
Folder Alarm
File Alarm_%Y_%M_%D
Chap.16 Work Operation
16-17
☞Set information on the target alarm
Set information on the target alarm as below.
Setting Item Setting Description
Target Node XP1(192.168.1.101)
Alarm Group Number 16777216
Alarm Group Number
For Alarm Group Number, see XP-Builder’s illustration screen.
If an alarm group is selected, the group’s ID will appear. Set the alarm number with the relevant group
ID.
Once editing the content as seen above is completed, data corresponding to the relevant alarm number
will be read from the subject node and written in Alarm_%Y_%M_%D File if the specified trigger conditions
are met.
Chap.16 Work Operation
16-18
A result file will be created at the specified folder and with name in the folder that has XP-Server’s
execution file.
Note
(3) Any Read-Only device cannot be set as a status device.
(4) Work ‘Read XGT Panel’s NVRAM Alarm’ creates CSV files every time.
Chap.16 Work Operation
16-19
16.8 Read XGT Panel Screen-Shot File
Action
● Read
A file is created by bmp capturing a specified XGT Panel screen.
☞Set file information as below.
Setting Item Setting Description
Output Folder XGTPanel_Capture
Output File Capture_%Y_%M_%D
Target Node XP1(192.168.1.101)
Once editing the content as seen above is completed, XP1 screen will be captured and saved at specified
the folder and with name in the folder that has XP-Server’s execution file if the specified trigger conditions
are met.
- Example of Capture Screen -
Chap.16 Work Operation
16-20
Note
(1) Any Read-Only device cannot be set as a status device.
(2) Capture files will have extension BMP automatically.
(3) Function ‘Capture Screen’ may take different times depending on machine types. For XP30, it takes less than 3 seconds,
for XP50 or XP70, less than 5 seconds and for XP90, less than 10 second to activate. Therefore, it is essential to
appropriately define time-out time of XP-Server in which ‘Read XGT Panel Screen-Shot File’ is defined in order to have
normal operation.
Chap.16 Work Operation
16-21
16.9 Send E-mail on PC
Action
● Send E-mail on PC
E-mail can be sent with the specified information using SMTP Protocol.
☞Set information as below.
Setting Item Setting Description
IP Address or SMTP Server Name smtp.google.com
SMTP Port No. 587
Use SSL/TLS Check
My SMTP server requires authentication Check
Validate server certificate Check
User account UserID
Password UserPassword
E-mail address reciver@gmail.com
Sender’s E-mail address sender@gmail.com
Title Title
Message Content
Once editing the content as seen above is completed, the mail will be sent if the specified trigger conditions are met.
Note
(1) Any Read-Only device cannot be set as a status device.
Chap.16 Work Operation
16-22
16.10 Start Application
Action
● Execute Program on PC
☞Set information as below.
Chap.16 Work Operation
16-23
Setting Item Setting Description
File Name C:Program FilesLSISXP-Manager 1.10XPManager.exe
Start Option
Start a new instance of application Check
In case of editing the content as seen above, execute the specified file name. It may be possible to
duplicate executing.
Note
(1) Any Read-Only device cannot be set as a status device.

Chap.17 XP-Server
17-1
Chapter 17 XP-Server
17.1 XP-Server’s Action Method
17.1.1 XP-Server’s Action Environment
If XP-Server is installed and the shortcut icon on the desktop or the program menu is clicked, the icon for XP-Server’s
control will appear on the work display line. Downloading to XP-Server starts upon the right click on this icon and the click of
[Start] Menu.
XP-Server is registered as Start Program when it is installed so that the icon for XP-Server’s control always appears on the
work display line whenever the system starts. This setting can be used if the user wants to start downloading to XP-Server
automatically when the system starts. The dialog box for setting XP-Server’s attributes will appear XP-Server if [Property] is
clicked from the menu, which appears upon the right click on the control icon and the user may conduct set this
arrangement in the dialog box.
Chap.17 XP-Server
17-2
17.2 XP-Server’s Control
17.2.1 Start and Stop
After installing XP-Server, double click XP-Server shortcut icon on the desktop to make XP-Server icon appear on the work
display line.
Since this icon appears on the work display line to provide the menu for controlling XP-Server’s action, the following context
menu generates upon the right click.
Click [Start] to activate XP-Server. If [Stop] is clicked, XP-Server’s action will stop.
17.2.2 Setting
(1) Set –Available Network interface
If [Attribute] is clicked from the XP-Server icon’s context menu, the window to set attributes will pop up. Among those
attributions, [Network] allows the user to decide which Ethernet interface of the computer in which XP-Server currently
runs is used for communication.
Chap.17 XP-Server
17-3
Chap.17 XP-Server
17-4
This setting is critical in case that the computer in which XP-Server currently runs has multiple Ethernet interfaces.
Assume that there are two Ethernet interfaces(E1:192.168.1.100, E2 : 192.168.1.150) and these two interfaces are
different from each other and they are connected with totally independent networks respectively. In addition, XGT
Panel is installed on the network to which E2 is connected. At this time, make sure to select 192.168.1 and 150 for
XP-Server’s network settings. That is, it is possible to communicate with XGT Panel only when XP-Server is
activated via E2 interface.
At this circumstance, it is also necessary to match with XP-Server’s IP set on XP-Manager. That is, a project may not
work normally on XP-Server if it is registered as E1 in the registration of XP-Server during the project edition on XPManager. XP-Server shall be registered as E2 as below.
(2) Set-Message Level
Message levels shall be classified into Basic, Normal and Detailed, and they decide which kind of message will be
displayed in the log file.
● Basic
Only messages on Start or Stop of the server and Fail to execute actions are displayed.
● Normal
In addition to basic-level messages, messages on failures caused by wrong entries by the user such as wrong
recipe number or alarm group number or failed reading/writing files when executing XP-Server or failed
communication with XGT Panel are provided.
● Detailed
In addition to normal-level, messages on the numbers of each action and whether it succeeds or not are provided.
Chap.17 XP-Server
17-5
Note
Action ‘Read/Write XP-Server Execution File’ may fail in the following cases:
(1) In case that the output directory of the action is designated to the system directory(C:Windows or C:Program Files are
paths in which system files for window operation systems are saved)
(2) Input and output directories of the action are designated to a disc (When attaching USB, designate a path and then
remove it) that cannot be found in the current system.
(3) Set-Auto Start XP-Server when the system starts
XP-Server starts automatically when the system starts
(4) Set-View Log
Once XP-Server starts, messages generated during the execution are recorded in the log file. Messages contain
various contents from notice on XP-Server’s starting and stopping to successful or failure results of individual actions
and it is possible for user to set message levels to which extent the message details are presented on [Message
Level]. If [View Log] button is clicked, a list of messages generated during the execution and saved in the text file will
appear.
(5) Directory
[Directory] tap sets where the files downloaded from XP-Manager will be saved.
Chap.17 XP-Server
17-6
● Form Path
Set a location in which Excel form files downloaded from XP-Manager will be saved.
● Input Data Path
When XP-Server runs, set a path in which ‘Write Original File’ will be saved. That is, if the input data path is set as
seen in the figure, the user will specify the original CSY file when editing the project on XP-Manager in case of Action
[Write XP-Server’s Recipe – CSV] and this file will be saved in Path E:TempDatainput.
● Output Data Path
When XP-Server runs, set a path in which output files created by XP-Server will be saved.
If setting is completed as above, Screen Capture File will be saved in Path E:TempDataoutputuser1capture.

Categories
Tags	IHM